The Egyptians used levers to lift the capstone to a height of 6.1 metres, then 4 or 5 men were able to use levers on stones less than 1 ton to flip them over and transport them by rolling, the larger stones had to be towed. They would use ramps to transport the stone to the top of the pyramid

Tools And Recourses

you would need ramps, levers and stones in order to lift the capstone

Challenges

2 major challenges would be bringing the capstone up to the top of the pyramid because of it's significant height and substantial weight witch adds to the difficulty.

Interesting fact

The term capstone comes from the final decorative "cap-stone" used to complete a building or monument, and they transported the capstone up a 147 metre tall pyramid.

Tools: Some of the necessary tools included copper items such as chisels, drills, and saws, which might have been used to cut the relatively soft stone. You would also need stuff like around 5.5 million tonnes of limestone and the amount of people well we aren’t exactly sure but Herodotus, the Greek historian, wrote that 100,000 workers built the pyramids and modern Egyptologists come up with a figure more like 20,000 workers.

Challenges: One of the main challenges faced during the placement of the pyramid was the precise angling and construction in alignment with the compass, ensuring that it faced the North Pole.

Facts:

• The Three Giza Pyramids Are Aligned.

• The Pyramid Texts Are the Oldest Known Religious Texts in the World.

• The Pyramids Were Actually White.

Tools: All they needed was the tombs and artifacts the pharaoh would want to bring to the after life.

Challenge: This was the main challenge, after the people entered the pyramid, they could'nt come out, so they sacrificed for their belief, the great khufu pharoah.

Fact: One fun fact is that when scientists discovered the pyramid no artifacts nor tombs were found in it, we believe it was looted before we found it.

The Great pyramid of Giza consisted of layers of stone blocks, with the lower layers being larger. Wooden barges transported stone blocks through canals and sluices. Our stage is the most important because without a base for the pyramid, it will all just collapse.

Challenges:

They were building the pyramids outside in the middle of the dessert and it would be very hot and tiering for them. This was definitely one of the biggest challenges they faced whilst building the pyramids.

Facts:

A fact about the great pyramid of Giza is that they used 6 million tons of bricks were lifted without technology. Around 2.3 million bricks, roughly weighing around 2.5 tons each were used to build the pyramids of Giza.

Tools: They used copper and stone-cutting tools to carve out the blocks in the quarries. Stones can also be cut by copper chisels and hammers.

Challenges: Some harder stones cannot be cut with copper tools. Therefore, we would have to use time-consuming ways like drilling and sawing. Each stone was around 2500 kg so we had to use sleds likely lubricated by water to transport the stones so they were easier for us to move them. Then we used levers, ramps, and pulleys to move the stone blocks away from the quarry site.

Facts: Due to the low-advanced technology used at that time, many blocks were detached, and some outer casing stones fell completely from a 1303-strong earthquake.

Materials:

. wooden sleds

. ropes

. Water

. Slaked lime

. Tafla

Facts:

. The heaviest stone is 25 to 80 tones which was found above the "King's" chamber

.The complex structure would've required modern technology to construct.

Challenges:

One of the major challenges the builders had to face was having to move such heavy and massive stones. Placing just one stone took around 2-3 minutes.

The materials they use were bricks, earth and sand, to reach up to the top they use equipment's like ramps, sledges, rollers and levers.

The challenge of building the sides of the Great Pyramids is hard to make sure every side is been built evenly, and to connecting the sides.

The internal chambers in the great pyramid of giza consisted of 3 main chambers, along with other passages and staircases. The purpose of the chambers was to store the body and soul of pharaohs, as the Egyptians believed this sent them in to the afterlife well.

Tools and Resources:

We used a stone cutter and carvers to cut passageways into the pyramids, we used this to cut chambers such as the King’s Chamber, the Queen’s Chamber, and the Sarcophagus which we were going to put King Khufu, but he changed his mind. We also made air ways to allow light to get into the pyramids

Challenges:

Constructing the chambers within and below the pyramids often had many challenges. The tight passageways we had to navigate to reach the internal chambers posed a significant challenge. The airflow while we were working often dropped to life-threatening levels very small holes that allowed air to pass through, putting myself and other workers at risk. In addition, poor cuts in the stone could lead to the chambers collapsing, as the pyramids were constructed from a weak type of limestone.

Interesting Fact:

The Kings chamber came before the pyramids were built but the King Khufu wanted a massive pyramid for him to die in.