Subject: How to make a wood stove by yourself.

 
Dear Bob,

How’re things going?

I hope well, I’m sorry it’s taken me so long to get back to you I've had a lot of work.

I think it’s an excellent idea that you want to build a wood stove in your backyard so you can have barbecues on Sundays.

But come on! How are you going to spend so much money on that?
I'll explain how to do it yourself and you'll save a few dollars.

To build your own wood stove, you first have to take into account the materials and tools you need.

6 bags of 20 Kg of screened earth (fine).
9 bags of screened sand.
1 bag of gravel and a little ash.
1 bag of cement.
4 galvanized pipes for the chimney.
1 chimney cap.
1 tile for the entrance of firewood.
1 metal base to put the fireplace.

To make the mold you need the following materials:

Drawer: Four metal sheets with four rods to adjust it and two more rods to level the pieces.

Metallic mold: For the entrance of firewood.

Combustion chamber: Two metal molds for the griddles.

4 burners
4 metal tubes
2 blades
1 trowel

When you have all this you are ready to start, now I will tell you the step by step.

Step 1. Create the base of the kitchen:

Before building the kitchen it is necessary to have the base or table ready. The standard size is 1.20 m x 1.20 m and 60 cm high. The base can be built with stones, adobe, brick, wood or iron. It can be full or hollow, the latter being the one with the greatest advantages. It is a usable space to store firewood or kitchenware.

Step 2. Drawer assembly:

It is placed on the base with the four metal pieces. We must make sure that the rods fit well in the holes so that the structure does not fall apart.

Step 3. Make the mix:

Mix the sand and soil with the cement until you get a uniform color and add water. Stir until sticky.

Step 4. Filling the kitchen:

Put an insulating layer on the base.
Add gravel to conserve heat.
Pour the first layer of the mixture and press it well.
Place the mold of the firewood entrance and place the tile on top.
Place the combustion chamber mold, adjusting it until the rod passes through each hole and ends up through the drawer.
Second layer of mix.
Third layer of mix. With it, it will be filled up to the level of the holes where the tunnels will go. Finish pressing.
Add more mixture in the place destined for the small stoves.
Place the tunnel molds by drilling or filling, as needed.
Place the base of the tube that integrates the tunnels. The rods must butt against the base.
Last layer of mix. In this part, press until the kitchen is level with the upper part of the drawer.
Smooth the kitchen surface.

Step 5. We remove the mold:

Pull out the two rods above the burners.
Remove the tunnels by unhooking them.
Turn the molds of the small stoves and take them out.
Take the dove out of the large stove and pull it up until the mold is removed.
Remove the rods from the drawer and carefully remove the sheets.
Extract the mold from the firewood entrance.

Step 6. Place the metal molds.

Fit or mold these parts well, sealing it properly to prevent heat or smoke leaks.

Step 7. Place the chimney pipes:

Place them on the base, then tape the tube to the ceiling or wall to prevent it from moving.

Step 8. Turn on the stove:

Before carrying out this step, it must previously be allowed to dry completely for approximately 4 days.

It takes a bit of work but I assure you it is totally worth it.
I was very specific buddy, you can't go wrong, I know you'll do well.
By the way For the kitchen to work properly and have a long life, it is essential to take care of it and carry out regular maintenance.
Always remove the ash, clean the stoves, the flues and the chimney tube from time to time, remove the soot from the flues and gently tap the chimney tube so that the soot falls down and you can remove it.

Anyway, I should get going.
You will do an excellent job if you follow the instructions well.
Don't forget to write me back I want to know the result.
And let me know if you need help.

 Best wishes,

Marianela Soto.

 

You solely need to buy a new wheel, wiper washer and lights

Let’s start you have to put your car in a safe place.

Raise the mobile arm and put it vertically then remove damaged wiper and put the new wiper now repeat the same process with the another wiper and finally Check the operation of the new wipers.
To repair the lights

 

 

 

Finally to change the wheel park in a safe place don't forget the parking brake then release the pressure of the studs and lift the car with a hydraulic jack you must remove the tire you are going to change and put the new one and then you have to put the car on the ground and that would be all good luck

Best regards
Alexander Angulo
84-69-02-98
alexanderangulo35@gmail.com

The first is to determine what type of fruit trees you want, the lemon is the most appreciated, so I recommend you plant lemon trees.

step two. You should plant the trees in late winter. You will need pots, I recommend clay pots because they retain moisture better and have a longer life.

Step three. You must define the size of the pots because every two or three years you will need to transplant them.

Step four. Good drainage, essential for growing fruit trees in pots, for this you can use gravel or volcanic clay. Perlite is a great ally for fruit trees in pots, as it helps to drain while maintaining moisture.

Step Five Choose a rich substrate and fertilize, because potted fruit trees need rich soil. You will also need worm castings to feed the soil.

step six. Take care of irrigation, in quantity and quality of water, every week you should water the trees, hopefully with rainwater. I recommend that you place the pots in a sunny location protected from the wind so that the trees can bear fruit. If you have doubts call me.

Best regards.

Roxana Díaz

Subject: How to Fix your computer.

Dear Mary 

I hope you are well. I am sorry to hear that you are having problems with your computer again. Why don´t you try to fix it yourself because hiring a technician is very expensive. And Also, some general computer issues can be addressed without seeking professional help. This are some basic steps you can take to repair your computer:

You must back up your files before trying to do anything.  This is the most important step, so you don’t lose important information. You can back up your files to an external hard drive, or a cloud storage service, like iCloud, DropBox, or Google Drive.

You can often fix a computer problem by shutting down the computer, then unplugging it. Then holding down the power button for 30 seconds while the computer remains unplugged. If this didn´t work, you can review your drivers or programs and update them if they are outdated. Computers may freeze because of any hardware or software issue. Notice if the issue started when you connected any hardware like a printer or scanner, or maybe the problem started after you downloaded a program, if your problems started after one or both situations, you should uninstall them. 

You also should Check your CPU and memory usage because some programs use to much memory and that can cause your computer to slow down or freeze.

If neither of this recommendations work, you should restore your computer. And don’t forget to have a good antivirus. 

I hope my recommendations have helped you. I Will be waiting for an updated in your computer state.  

Goodbye, I hope I can visit you soon, I miss you a lot.

Alyssa. 

Right now I don't have money to lend you but I can help you with a few things to make your vase, I'm sure you have plastic bottles at home.

Things you will need:

a plastic bottle,pair of scissors,a utility knife,decorate the bottle,a plastic bottle,pair of scissors,a utility knife,a permanent marker,acrylic or spray paint,hot melt glue,

rhinestones,decals.

Step 1

Cut the top of the bottle just below where it curves inward.

Step 2

Level the top of the cut with scissors.

Step 3

Cut strips 2 inches (5 cm) long and ½ inch (1 cm) wide around the bottle.

Step 4

Fold the strips out to open the bottle.
Step 5

Place a strip above the one next to it.

Step 6

Tuck that strip under the next one.

Step 7

Work the same pattern around the entire bottle.

Step 8

Fill the bottle with water and flowers.

I hope this helps you in something and I will be waiting for the photos to see how the vases turned out.
 Hugs and kisses. bye


Annika Vindas
71325626