Reflection by Toh SF https://padlet.com/sftoh123/v62s442x8wbu8u6a Summarize what you have learnt today and state the procedure of building a tentage. en-us 2021-08-31 16:10:33 UTC 2021-09-01 11:36:29 UTC hello@padlet.com https://padlet.net/icons/png/1f3d5.png Name https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1707527014 Answer

]]> 2021-08-31 16:22:50 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1707527014 Name https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1707527224 Answer]]> 2021-08-31 16:22:56 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1707527224 William https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709481396 14 pegs are needed

6 pegs on one side
Other 6 on other side 
2 pegs on front and back]]> 2021-09-01 08:46:31 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709481396 William https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709483420
  • Assemble the horizontal pole and vertical poles together.
  • Put the Inner sheet onto the horizontal pole and insert the pins of the vertical poles through the sleeve ring.
  • Tie one end of the twine with bowline to the sleeve rings at the corner of the inner sheet.
  • Check that the pegs, the corner of the inner sheet and the middle of the horizontal pole are in a straight line.
  • Hammer at least half of the pegs 45° into the ground, keeping a distance of at least 45cm from the corner of the tent.
  • Tie all the four guylines to the pegs with tent-guy loop at the same time or at least the two diagonal pairs should do it together. Also ensure that the wall flap is just above ground. 
  • Tie the two side guylines after the corner guylines have been secured and make sure that the three pegs on each side are in a straight line 
  • Tie the two main guylines to the pins on the vertical pole using clove hitch and also tie the other end to the pegs at about the length of the vertical pole away from the bottom of the vertical pole using tent-guy loop.
  • Put the Outer sheet onto the horizontal pole and insert the pins on the vertical poles through the sleeve ring.
  • Repeat the procedure 3 to 7 for the outer sheet.
  • Roll the window flaps neatly and tie them up. Tidy up all the loose ends properly.
  • Unfold the ground sheet and lay it flat inside the tent. If the ground sheet has any overlying area, fold it neatly underneath the ground sheet.



    • ]]>     2021-09-01 08:47:48 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709483420     Madhu durai_karikalan_madhu_mitha https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709483712 When choosing a campsite, we need to find elevated land or a gentle slope to prevent flooding.]]> 2021-09-01 08:48:01 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709483712 arjay https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709485054  when choosing a campsite need to find a place where it can prevent flood]]> 2021-09-01 08:48:58 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709485054 Brianne ang_li_xuan_brianne https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709485231 Do not pitch a tent underneath a tree because dead branches might fall on it]]> 2021-09-01 08:49:06 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709485231 Leon li_yangguan_leon https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709485876 Stop pegging when peg is one palm away from the ground.
    Ensure that no one is nearby you when pegging.
    Do not swing your hand too high when pegging.]]>     2021-09-01 08:49:31 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709485876     Yaqi leong_ya_qi1 https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709487283 Clear rocks and wood before pitching the tent]]> 2021-09-01 08:50:29 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709487283 Javier https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709488311 Remove everything when pitching a tent]]> 2021-09-01 08:51:12 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709488311 yuya yuyahninmoe https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709488379 when choosing a place to pitch a tent, choose a place that prevents flooding]]> 2021-09-01 08:51:15 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709488379 Adam salinasuyod https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709489097 logistics required
    1 x inner sheet
    1x outer sheet
    1x groundsheet
    1xhorizontal pole
    2x vertical poles
    2x2.5 twine(main guylines) 1m+1.5m
    12x1.5 twine (corner/side guylines)
    14xmetal pegs
    1x mellet]]>     2021-09-01 08:51:29 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709489097     Madhu durai_karikalan_madhu_mitha https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709491031 a) Fix the horizontal pole to the vertical poles. Then place the inner sheet across the horizontal pole.

    b) Secure one end of the guylines to each of the corner sleeve ring with a bowline.

    c) Hammer at least half of the peg 45o into the ground, keeping a distance of about 45cm from the corner of the tent.

    d) All the 4 guylines should be tied using the tent-loop, at the same time if possible. If not, the diagonal corners should at least do it together. Ensure that the all flap is just above the ground.

    e) Tie the two side guylines after the corners are secured and ensure that the three pegs on each side of the tent are in straight line.

    f) Secure the main guyline to the pins using clove hitch.

    g) Place the outer sheet over the inner sheet and repeat the above procedures for the outer sheet.

    h) The distance of the pegs for the main guy lines should be about the length of the upright from the base of the vertical pole.

    i) Window flaps should be rolled up and tied. All loose ends should be properly tidied.

    j) Unfold the groundsheet inside the tent and lay it out. All overlying area of the groundsheet should be folded neatly underneath the groundsheet itself.

    k) The tent should have a ventilation gap of about 15 – 20cm between the inner and outer sheets.

    l) All guyline should meet the pegs at 90 degree.



    ]]>     2021-09-01 08:52:12 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709491031     Ke Yu https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709492057 Don’t hang clothes over the tent to dry ]]> 2021-09-01 08:53:02 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709492057 Gabriella gabriellaong https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709497051 a) Fix the horizontal pole to the vertical poles. 
    Then place the inner sheet across the horizontal pole.

    b) Secure one end of the guyline to each of the corner sleeve ring with a bowline.

    c) Hammer at least half of the peg 45o into the ground, keeping a distance of about 45cm from the corner of the tent.

    d) All the 4 guylines should be tied using the tent-loop, at the same time if possible. If not the diagonal corners should at least do it together. Ensure that the all flap is just above the ground.

    e) Tie the two side guylines after the corners are secured and ensure that the three pegs on each side of the tent are in straight line.

    f) Secure main guyline to the pins using clove hitch.

    g) Place the outer sheet over the inner sheet and repeat the above procedures for the outer sheet.

    h) The distance of the pegs for the main guy lines should be about the length of the upright from the base of the vertical pole.

    i) Window flaps should be rolled up and tied. All loose ends should be properly tidied.

    j) Unfold the groundsheet inside the tent and lay it out. Overlaying all area of the groundsheet should be folded neatly underneath the groundsheet itself.

    k) The tent should have a ventilation gap of about 15 – 20cm between the inner and outer sheets.

    l) All guylines should meet the pegs at 90 degree.


    ]]>     2021-09-01 08:55:12 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709497051     Leon li_yangguan_leon https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709499353 Find a spot suitable for setting the camp site, set up the poles inside the tent. Lay the ground sheet and peg the peg into the spot where it is suppose to be, and put the inner sheet on. Tie the ring on the inner sheet to the pegs in the ground then do the same for the outer sheet. ]]> 2021-09-01 08:56:39 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709499353 Gabriella gabriellaong https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709502643 When choosing a campsite the land must be elevated or gentle to prevent flooding]]> 2021-09-01 08:58:44 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709502643 Ke Yu https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709512834 • Fix the horizontal pole to the vertical poles. 
    Then place the inner sheet across the horizontal pole.

    • Secure one end of the guyline to each of the corner sleeve ring with a bowline.

    • Hammer at least half of the peg 45o into the ground, keeping a distance of about 45cm from the corner of the tent.

    • All the 4 guylines should be tied using the tent-loop, at the same time if possible. If not the diagonal corners should at least do it together. Ensure that the all flap is just above ground.

    • Tie the two side guylines after the corners are secured and ensure that the three pegs on each side of the tent are in straight line.

    • Secure main guyline to the pins using clove hitch.

    • Place the outer sheet over the inner sheet and repeat the above procedures for the outer sheet.

    • The distance of the pegs for the main guy lines should be about the length of the upright from the base of the vertical pole.

    • Window flaps should be rolled up and tied. All loose ends should be properly tidied.

    • Unfold the groundsheet inside the tent and lay it out. Overlaying all area of the groundsheet should be folded neatly underneath the groundsheet itself.

    • The tent should have a ventilation gap of about 15 – 20cm between the inner and outer sheet.
    ]]>     2021-09-01 09:06:16 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709512834     Brianne ang_li_xuan_brianne https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709537557 Fix the horizontal pole to the vertical poles. Then place the inner sheet across the horizontal pole. Secure one end of the guyline to each of the corner sleeve ring with a bowline. Hammer at least half of the peg 45o into the ground, keeping a distance of about 45cm from the corner of the tent. All the 4 guylines should be tied using the tent-loop, at the same time if possible. If not the diagonal corners should at least do it together. Ensure that the all flap is just above ground. Tie the two side guylines after the corners are secured and ensure that the three pegs on each side of the tent are in straight line. Secure main guyline to the pins using clove hitch. Place the outer sheet over the inner sheet and repeat the above procedures for the outer sheet. The distance of the pegs for the main guy lines should be about the length of the upright from the base of the vertical pole. Window flaps should be rolled up and tied. All loose ends should be properly tidied. Unfold the groundsheet inside the tent and lay it out. Overlaying all area of the groundsheet should be folded neatly underneath the groundsheet itself. The tent should have a ventilation gap of about 15 – 20cm between the inner and outer sheet.]]> 2021-09-01 09:25:49 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709537557 Richard https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709547198 Remove things that is near the place where you're going to place your tent for example rocks and woods]]> 2021-09-01 09:33:41 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709547198 Richard https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709550665 (1) Fix the horizontal pole to the vertical poles after that place the inner sheet across the horizontal pole.

    (2) Secure one end of the guyline to each of the corner sleeve ring with a bowline.

    (3) Hammer at least half of the peg 45 degree into the ground, keeping a distance of 45cm from the corner of the tent.

    (4) All the 4 guylines should be tied using the tent-loop, at the same time if possible. If not the diagonal corners should at least do it together. Ensure that the all flap is just above the ground.

    (5) Tie the two side guylines after the corners are secured and ensure that the three pegs on each side of the tent are in straight line.

    (6) Secure main guyline to the pins using the clove hitch.

    (7) Place the outer sheet over the inner sheet and repeat the above procedures for the outer sheet of the tent.

    (8) The distance of the pegs for the main guy lines should be about the length of the upright from the base of the vertical pole.

    (9) Window flaps should be rolled up and tied. All loose at the ends should be properly tidied.

    (10) Unfold the groundsheet inside the tent and then lay it out. Overlaying all area of the groundsheet should be folded neatly underneath the groundsheet.

    (11) The tent need a ventilation gap of about 15 – 20cm between the inner and outer sheets.

    (12) All guylines should meet the pegs at somewhere about 90 degree.
    ]]>     2021-09-01 09:36:43 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709550665     Yaqi leong_ya_qi1 https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709684589 a) Fix the horizontal pole to the vertical poles. 
    Then place the inner sheet across the horizontal pole.

    b) Secure one end of the guyline to each of the corner sleeve ring with a bowline.

    c) Hammer at least half of the peg 45o into the ground, keeping a distance of about 45cm from the corner of the tent.

    d) All the 4 guylines should be tied using the tent-loop, at the same time if possible. 
    If not the diagonal corners should at least do it together. Ensure that the all flap is just above the ground.

    e) Tie the two side guylines after the corners are secured and ensure that the three pegs on each side of the tent are in straight line.

    f) Secure main guyline to the pins using clove hitch.

    g) Place the outer sheet over the inner sheet and repeat the above procedures for the outer sheet.

    h) The distance of the pegs for the main guy lines should be about the length of the upright from the base of the vertical pole.

    i) Window flaps should be rolled up and tied. All loose ends should be properly tidied.

    j) Unfold the groundsheet inside the tent and lay it out. 
    Overlaying all area of the groundsheet should be folded neatly underneath the groundsheet itself.

    k) The tent should have a ventilation gap of about 15 – 20cm between the inner and outer sheets.

    l) All guylines should meet the pegs at 90 degree.


    ]]>     2021-09-01 11:36:29 UTC https://padlet.com/sftoh123/v62s442x8wbu8u6a/wish/1709684589