https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy How did I manipulate my flow rate to make the liquids go slower? en-us 2020-06-27 20:16:02 UTC 2020-07-10 17:16:17 UTC hello@padlet.com https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/648560562 I can put an obstacle in front of it to where the liquid has to go around the obstacle to reach the end or I can make an angle so the liquid isn't travelling directly down, which makes it slower.]]> 2020-07-06 18:48:44 UTC https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/648560562 https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/648563222 i can change the angle of the plate to make it level causing my liquids to go slower.]]> 2020-07-06 18:53:10 UTC https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/648563222 https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/648563983 I can alter the angle of my surface so that the liquids slow down, I can also place obstacles in front of them so the only way to reach the end would be to waste time and go around it.]]> 2020-07-06 18:54:25 UTC https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/648563983 https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/649358931 The smaller the angle my plate is positioned, the slower it travels, the bigger angle I tilt my plate, it travels faster.]]> 2020-07-07 16:49:39 UTC https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/649358931 https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/649369740 The smaller the angle the slower it goes down. the higher the angle, the quicker it goes down ]]> 2020-07-07 17:03:46 UTC https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/649369740 https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/649396614 If I slant the plate in a / angle the liquid will travel slower to the other side of the plate. If it is | angle it will go faster]]> 2020-07-07 17:38:44 UTC https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/649396614 https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/649424808 I put the plate horizontal the liquids went down the plate really quick, and when I put the plate horizontally the liquids slowed down.]]> 2020-07-07 18:17:39 UTC https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/649424808 https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/649451676 I just tilted the plate/surface so it was flat-er - it's not going to move very fast if the surface is flat. (I know everyone's doing this but it's the easiest to think of so hey-)

Besides that, I waited for my liquid to dry up a little then re-do it. It honestly didn't change much, but hey-it worked a little. Just even a little.]]> 2020-07-07 18:55:04 UTC https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/649451676 https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/650380691 I manipulated the flow rate by raising the plate higher instead of lower and closer to the ground to slow down the liquid a bit. I also titled the plate below 90 degrees, so the plate was nearly held flat.]]> 2020-07-08 19:04:50 UTC https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/650380691 https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/651172040 I manipulated the flow rate of my liquid by placing the liquid either at 180 degrees or fully down. This played a big factor on slowing down my liquid.]]> 2020-07-09 17:19:25 UTC https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/651172040 https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/651178165 I manipulated the flow rate by tilting the plate upwards. This is because the smaller the angle the slower the liquid travels because of, gravity?????]]> 2020-07-09 17:24:12 UTC https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/651178165 https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/651229833 If I want to slow down my liquid, then you need to lift the end of the plate, and when an object(a plate in this case) is angled to the floor, the gravity will pull it down, but if the end of the plate is lifted, it will be hard for the gravity to pull the liquid down because the liquid is already on the plate, and the gravity is pulling down the liquid to the plate, but IF it is angled to the floor, it will eventually slide down. ]]> 2020-07-09 18:37:13 UTC https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/651229833 https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/651920281 i turned my plate so that it has a smaller angle and also I twisted the plate upwards because when I put it down it goes faster]]> 2020-07-10 17:15:14 UTC https://padlet.com/pauloberoi2/t3wkctj1c4yrmkmy/wish/651920281