Save the Boulders Beach Penguins by Sydney Wolf https://padlet.com/wolfsydn/m1201yz6ih4k Created By Sydney Wolf en-us 2018-02-08 18:43:49 UTC 2023-05-30 15:39:24 UTC hello@padlet.com Step 1: Identify the Problem wolfsydn https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229754503 Global warming is causing penguins in South Africa to overheat. When they go into water to cool off, birds are stealing their eggs.]]> 2018-02-08 18:46:42 UTC https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229754503 Step 2: Research the Problem wolfsydn https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229754942  1. Mylar
2. Cotton
3. White felt]]> 2018-02-08 18:47:29 UTC https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229754942 Step 3: Brainstorm Possible Solutions wolfsydn https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229755742 The tray demo and spoons demo showed which bottom material would be the best. The black vs mylar demo shows which material would be used for the roof.The atic vs floor demo shows where should put the penguin in the house.]]> 2018-02-08 18:48:47 UTC https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229755742 Step 4: Select One Solution wolfsydn https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229756048 We used mylar for the roof and the walls. We used cotton balls for the floor inside. We used black paper as a thin layer inside the mylar walls.]]> 2018-02-08 18:49:19 UTC https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229756048 Step 5: Construct a Prototype wolfsydn https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229756357 2018-02-08 18:49:54 UTC https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229756357 Step 6: Test Prototype wolfsydn https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229756496 A success we had was that we had a less percent loss. A failure we had was that our design kept falling over during the testing. Our percent failure was 23%.]]> 2018-02-08 18:50:09 UTC https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229756496 Step 7: Modify Design to Improve it wolfsydn https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229756765 We changed it by adding Popsicle sticks to the bottom for support.]]> 2018-02-08 18:50:35 UTC https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229756765 Step 8: Present and Redesign if needed wolfsydn https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229757158 Our success was that the house stayed up, it did not fall down. Our failure is that we added .13 to the percent lost. Our final percent loss was 23.41. If I did this project again, I would make it so that the walls were stronger, and I would put more insulator in them.

]]> 2018-02-08 18:51:11 UTC https://padlet.com/wolfsydn/m1201yz6ih4k/wish/229757158