https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl Collaborate with a partner and research Plugins. Then share your findings here en-us 2017-02-21 21:15:37 UTC 2025-09-28 06:19:34 UTC hello@padlet.com https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155530706 equalization is the process commonly used to alter the frequency response of an audio system using linear filters. 
How does Equalization work? Equalization adjust the amplitude of audio signals at particular frequencies
Why would we use the Equalization? Equalization may also be used to eliminate or reduce unwanted sounds or make the voice on a mic sound louder.]]> 2017-02-22 17:33:21 UTC https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155530706 https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155531123 They are modulation effects, that utilize a bit of delay and alter that delay over time while playing.  This causes harmonics to phase cancel and  creates a sweeping up and down sound with the instrument or sound.

Chorus works similarly in the way that it uses the same effect, but over a more specific frequency range. da dum tss]]> 2017-02-22 17:34:33 UTC https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155531123 https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155535073 chorus]]> 2017-02-22 17:44:40 UTC https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155535073 https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155536100 1.An effect whereby the sound produced by an amplifier or an amplified musical instrument is made to reverberate slightly.
2.The amp has a small output stage (about 1 watt) that sends the guitar signal out to drive the tank. The springs get excited with teh sound and create the reverb sound. Then a "recovery" stage (similar to the input stage your guitar plugs into) brings the reerb signla back in and mixes it with the straight sound.
3.The reverb projects the mental image (and other associated sensations) of the imagined space in which the sound was recorded. Reverb is used for a few different reasons in a mix. Reverb can also be used as a creative effect or sound design tool.]]> 2017-02-22 17:47:02 UTC https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155536100 sal_bustos2000 https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155536711 A noise gate or gate is an electronic device or software that is used to control the volume of an audio signal. Comparable to a compressor, which attenuates signals above a threshold, noise gates attenuate signals that register below the threshold.^[1] However, noise gates attenuate signals by a fixed amount, known as the range. In its most simple form, a noise gate allows a signal to pass through only when it is above a set threshold: the gate is 'open'. If the signal falls below the threshold, no signal is allowed to pass (or the signal is substantially attenuated): the gate is 'closed'.^[2] A noise gate is used when the level of the 'signal' is above the level of the 'noise'. The threshold is set above the level of the 'noise' and so when there is no 'signal', the gate is closed. A noise gate does not remove noise from the signal. When the gate is open, both the signal and the noise will pass through. Gates typically feature 'attack', 'release', and 'hold' settings and may feature a 'look-ahead' function.]]> 2017-02-22 17:48:33 UTC https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155536711 yourenotkawaii1230 https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155537602 A noise gate or gate is an electronic device or software that is used to control the volume of an audio signal. Comparable to a compressor, which attenuates signals above a threshold, noise gates attenuate signals that register below the threshold. However, noise gates attenuate signals by a fixed amount, known as the range. In its most simple form, a noise gate allows a signal to pass through only when it is above a set threshold: the gate is 'open'. If the signal falls below the threshold, no signal is allowed to pass (or the signal is substantially attenuated): the gate is 'closed'. A noise gate is used when the level of the 'signal' is above the level of the 'noise'. The threshold is set above the level of the 'noise' and so when there is no 'signal', the gate is closed. A noise gate does not remove noise from the signal. When the gate is open, both the signal and the noise will pass through. Gates typically feature 'attack', 'release', and 'hold' settings and may feature a 'look-ahead' function. 

]]> 2017-02-22 17:50:52 UTC https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155537602 https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155538410 WHAT IS IT? 
its a technique used in sound recording and mixing
 
HOW IT WORKS
It is achieved by using two different compressors in a signal chain. one compressor generally stabilizes the dynamic range of all the other aggressively compress stronger peaks

USES
Compression often used to make music sound louder with out increasing its peak amplitude.]]> 2017-02-22 17:52:59 UTC https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155538410 https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155538523 2017-02-22 17:53:13 UTC https://padlet.com/jacobswellkeyboardguy/hw4ugz99m3zl/wish/155538523