# data[].attributes.body
goold = changing motor bike tiles

material = new tire tire wre nch ais pump

steps = a. motor bike parking in its place

b. thraw cut the air thut is stil in the

c.pry off old and loose tires

d.instal new tires

e. pump the tire untiq itis filled with

endugh air

# data[].attributes.body
Material

1.spark plug key

2.pliers

3.suster

Steps

1.make sure the motorbike inghtion key in is the off positif

2.poll slowly removing the coil cable thay connects to the spark plug

3.Remove the old spark plug using a spark plug wrench

4.install new spark plugs tightn then using a spark plug wrench

5.reinstall the coil cable on the connect spark plug

# data[].attributes.body
Goal :

Changing oil motorcycle

Material :

Oil

Receptacle

Funnel

Pliers

Key ring

Step :

1. Warm up the motorcycle engine for about 3-5 minutes to make the old oil thinner

2. Turn off the engine and place the motorcycle on the center stand

3. Use the wrench to open the drasin bolt under the engine

4. Let the old oil flow out completely into the receptacle

5. Tighten the drain bold again after the oil is drained

6. Pour new oil into thi engine through the oil filler hole using a funnel

7. Check the oil level with the dipstick to make sure it's enough

8. Start the engini for afew minutes to circulate the new oil

9. make sure thire are no oil leaks around the drain bolt

# data[].attributes.body
1.riski

2.sidiq

3.rafkah

# data[].attributes.body
Anggota Kelompok:

1. Zildan R. S.

2. Kevin A.

3. Ivander G. F. P

4. Alfian D. T

# data[].attributes.body
Kelompok:

Danang

Damar

Bagas

Matrial:

1)paint 6)brake over

2)Sanderpaper 7)comperessor

3)water 8)spary gun

4)bucket

5)duster

Steps:

1)clean alld sand the rim surfance until smooth

2)then spary a base Coat aof primer of epay after Ward

3)apply the base calor thinly and eyenly in 2-3 conts

4)and finis with a clear for a glossy

5)long lasting finish

# data[].attributes.body
Material: kompresor, nitrogen, Tire pressure gauge

Steps:1.Park the car in a safe and level

place.

2.chek the caatr's Tire pressure.

3.prepare the tools.

4.remove the Tire valve cap.

5.attach the compressor hose to the stem.

6.check the the pressure regularly.

7.reduce the Tire pressure.

# data[].attributes.body
Material

-Oil

-Receptacle

-funnel

-picrs

-key ring

Step

1 warm up the motorcycle engine for about 5 minutes to make the old oil thinner

2 turn off the engine and place the motorcycle and on the center stand

3 use the wrench to open the drain bolt under the engine

4 let the old oil klow out complety into the receptasi

5 tighten the drain bolt again after the oil is drainded

6 pour aew oil into the engine through the oil filler hole using a funep

7 check oil level which the dipstick to make sure it's enough

Kelompok

Amanda

Roki

# data[].attributes.headline
Goal:to splace a flat tire with a spase trice in a marmer  

# data[].attributes.subject
Goal:to splace a flat tire with a spase trice in a marmer  

# data[].attributes.body
Nama anggota:

+Sultan

+AGAM

+Revan

Material:-spare tire

-jack

-Lucg werench

Step. : 1) turun an your nazald linght and full over to a sate place

2) e ngaga the parking brake

3) open the truck and take out the spare tiri hack.and lug wpech

4) place the car wander the car Nias the flat tine

5)raise the car vntil the flat tire is of gleound

6)losen and frem over the lugnuts fro theflet tire

7)take off the flat tire and putthe spare tire on the well

8)tighten the lugnuts nuts by hard

9)locker the car and forever the Jack

10)use the lugnuts Loren touful

# data[].attributes.body
material =socket wrench, screw driver, gasoline, brush

steps =

-remove components and loosen bolts

-clean the component with gasoline and a brush

-check for damaged components and replace them

-reinstalk the carburator components and attack them to the manipold then tighten the bolts

-turn on the motorcycle and check if it is working property