# data[].attributes.body
1. clamp pressure increase
2. lower injection pressure
3. increase preheat temperature
4. decrease mold closing
5. increase clamp pressure

# data[].attributes.body
1. Add breathe cycle
2. increase cure time
3. increase preheat temperature
4. increase hold pressure
5. slow down rotation screw

# data[].attributes.body
1. Increase curing cycle
2. Do well in venting
3. Increase preheat temperature

# data[].attributes.body
1. Select a less viscous polymer with higher flowability. The polymer will reach and fill the hardest to reach the cavities.
2. Increase the mold or melt temperature.
3. Increase the material feed in the molding machine .

# data[].attributes.body
1. Increase the clamp pressure to ensure the mold parts remains shut during shots.
2. Ensured the mold is properly maintained and cleaned (or replaced when it has reached the end of its useful lifespan).
3. Adopt optimum molding conditions like injection speed, injection pressure, mold temperature and proper gas venting.

# data[].attributes.body
1. Increase "mold closes" portion of cycle help in minimize blisters
2. Increase of back pressure may help in removing gases before they enter the mold.
3. Slowing down screw rotation will minimize the amount of air drawn into material.
4. Increase mold temperature will help gases escape by delaying the hardening of surface skin.

# data[].attributes.body
1. increase barrel temperature
2. increase back pressure of the screw
3. increase mold temperature
4. increase holding pressure
5. increase melt temperature

# data[].attributes.body
1. Increase mold temperature
2. Increase preheat temperature
3. Decrease mold closing speed
4. Check condition of mold plating and re-plate if necessary
5. Polish mold
6. Apply mold release agent
Imran Hakim Bin Mohammed
55216115389

# data[].attributes.body
1. lower mold temperature
2. lower melt temperature
3. lower injection pressure

# data[].attributes.body
1. increase mold temperature
2. increase melt temperature
3. use less viscous material
4. increase injection pressure

# data[].attributes.body
1. slow down the injection rate.

2. bring the second-stage (pack/hold) pressure to the minimum the machine allows

3. Clean mold surfaces and behind slides and inspect cavity for any obstruction to proper clamping.

4.Reduce clamp tonnage

5. Minimize melt residence time

6. Check number, placement, and length of support pillars in mold
Imran Hakim B Mohammed
55216115389

# data[].attributes.body
1.increase mold temperature
2. increase cooling time
3. decrease injection speed
4. increase back pressure
5. decrease screw speed rotation
6. increase the 'mold closed' portion of cycle

# data[].attributes.body
1. Eliminate air traps

2. increase mold and melt temperature

3. Increase ram speed

4. Change part geometry

5. Change material

6.Increase closing speed

Imran Hakim B Mohammed
55216115389

# data[].attributes.body
1) Increase cure time
2) increase mold temperature
3) Employ the breath during cycle
4) Increase preheat temperature
5) Increase cycle time
6) Slowing down the screw rotation will minimize the amount of air that is drawn into the material which cause blister

Imran Hakim b Mohammed
55216115389

# data[].attributes.body
1. select less viscous plastic with higher flowability.
2. increase mold and melt temperature.
3. increase the material feed

# data[].attributes.body
1. increase cure time
2. polish tool
3. increase weight to mould

# data[].attributes.body
1. Increase cure time
2. Increase mould temperature
3. Increase preheating
4. decrease mould temperature
5. employ a breathe during cycle
6. preheat powder

# data[].attributes.body
1. Increase charge weight.
2. Increase preheat temperature.
3. Increase mold closing speed.
4. Decrease mold temperature.
5. Check mold venting and correct as needed.
6. Use high pressure

# data[].attributes.body
1. Increase mold temperature.
2. Increase preheat temperature
3. Decrease mold closing speed
4. Check condition of mold plating and re-plate if necessary. If mold is unplated,

polish or plate it.
5.  Polish the mold.
6. Increase cure time

# data[].attributes.body
1. Reduce Charge weight
2 Increase preheat temperature.
3.Increase mold temperature.
4. Decrease mold closing speed.
5.Check parting line for wear or damage and correct as needed.
6.Increase clamp tonnage if possible.

# data[].attributes.body
1. Reduce mould wall temperature.

2. Reduce injection rate.

3. Increase holding pressure.

4. Optimize back pressure.

5. Optimize screw speed.

6. Reduce curing time.

# data[].attributes.body
M
1) Decrease charge weight
2) Increase preheat temperature.
3) Increase mold temperature.
4) Decrease mold closing speed.
5) Check parting line for wear or damage and correct as needed
6) Increase clamp tonnage if possible
7) increase cure time
Polish tool
8) Chromium plate tool

# data[].attributes.body
1)  Decrease charge weight.
2) Increase preheat temperature.
3) Increase mold temperature.
4) Decrease mold closing speed.
5) Check parting line for wear or damage and correct as needed.
6) Increase clamp tonnage if possible

# data[].attributes.body
1) Increase melt temperate
2) Raise the temperature within the service range
3) Replace the back-flow prevention ring
4) Increase screw speed
5) Applying a high pressure
6) Increase the cooling water volume at the hopper opening

# data[].attributes.body
1) Increase cure time
2) increase mold temperature
3) Employ the breath during cycle
4) Increase preheat temperature
5) Increase cycle time
6) Slowing down the screw rotation will minimize the amount of air that is drawn into the material which cause blister

# data[].attributes.body
Blisters :

1. increase back- pressure

2. increase the ``mold closed'' portion of the cycle.

3. Reduce the injection speed

4. increase the mold temperature

5. Gates should normally be located in the thickest section of the part.

6. Increase cure time

Short shot :

1. Eliminate air traps

2. increase mold and melt temperature

3. Increase ram speed

4. Change part geometry

5. Change material

6. Increase closing speed

Dull appearance :
1. change in flow-front velocity

2. Low melt temperature

3. increase the barrel temperature

4. increase the screw backpressure

5. Increase cure time

6. Increase charge weight to mould

Excessive flash :

1. slow down the injection rate.

2. bring the second-stage (pack/hold) pressure to the minimum the machine allows

3. Clean mold surfaces and behind slides and inspect cavity for any obstruction to proper clamping.

4. Reduce clamp tonnage

5. Minimize melt residence time

6. Check number, placement, and length of support pillars in mold.

# data[].attributes.body
1. increased the barrel temperature
2. increased the mold temperature.
3. increase the back pressure.
4. increase the speed of screw rotation.
5. do well in venting
6. increase the curing cycle

# data[].attributes.body
1. increase the cycle time
2. slow down the screw rotation speed.
3. decreased the injection speed.
4. increased the mold temperature.
5. increased the back pressure.
6. increased the curing time

# data[].attributes.body
1. increase the clamp pressure
2. ensure that the mold is properly maintained and cleaned.
3. decreased the mold closing speed

# data[].attributes.body
- increase the injection pressure
- increase the cooling time
- increase mold and melt  the temperature
- eliminate the air traps
-select a less viscous material
- e

# data[].attributes.body
-increase cure time
-increase charge weight to mold
-reduce mold temperature
-reduce cure time

# data[].attributes.body
-increase back pressure
-increase mold temperature
-increase cure time
-increase screw speed

# data[].attributes.body
-reduce weight of resin added to tool
-choose easier flowing material

# data[].attributes.body
1. select the less viscous material with higher flowability
2. increase mold temperature
3. increase the material feed
4. increase RAM speed
5. increase the injection pressure
6. select a less viscous material

# data[].attributes.body
1.increase the ``mold closed'' portion of the cycle
2. Reduce mold temperature
3. increase the injection pressure

# data[].attributes.body
1. Component is undercured
-increase mold temperature
-increase cure time
-increase preheating

# data[].attributes.body
1. increase the clamp pressure
2. clean the mold properly
3. checking the parting line
4. optimal the mold temperature
5. decrease the injection pressure
6. checking the material flow

# data[].attributes.body
1. increase the mold temperature
2. raising the screw back pressure
3. increase the cure cycle
4. increase molding pressure
5. polish tool surface

# data[].attributes.body
1.Increase melt temperature
2.increase backpressure
3.use less viscous material
4.Polish the mold

# data[].attributes.body
1. increase mold temperature.
2. increase pre heat time
3. increase screw speed
4. reduce mold closing speed
5. consistent polishing and cleaning of mold

# data[].attributes.body
1. preheat material before used
2.store material in moisture protective barrier
3.inçrease holding pressure and holding time
4.Ensure proper ventilation in mold
5.use less viscous plastic to allow gas escape rapidly
6.increase breathe cycle
7.Reduce injection speed
8.Reduce mold closing speed

# data[].attributes.body
1. decrease mold clamping pressure
2.reduce injection pressure
3.reduce injection speed
4.reduce melt temperature
5.use less viscous material
6.reduce screw speed
7.reduce mold temperature
8.reduce mold clamp force
9.Check parting line for wear or damage and repair if needed

# data[].attributes.body
1. increase clamp pressure
2. reduce injection pressure
3. Decrease mold temperature
4.  decrease residence time
5. reduce cycle time

# data[].attributes.body
1.Ensure mold is properly vented to avoid gas entrapment
2.Add more material
3.Increase mold pressure and temperature
4.Increase melt temperature
5.Ensure no blockage at the nozzle tip as well as at the sprue bushing at the mold
6.use less viscose material
7.increase runner diameter
8.increase sprue diameter
9.use short sprue bushing

# data[].attributes.body
1. increase the pre-heat time
2. add breath cycle
3. increase mold temperature
4. reduce injection speed
5. increase back pressure

# data[].attributes.body
1. increase the amount of material
2. increase mold temperature
3. increase injection speed
4. increase hold pressure
5. increase screw speed

# data[].attributes.body
1.  take care the mold by polishing it.
2.  Increase the mold temperature.
3.  use mold release agent.
4.  decrease the closing speed of the mold.
5. increase the pre-heat time
6. check the plating condition.

# data[].attributes.body
1. increase the amount of materials
2. increase material viscosity
3. use high pressure
4 decrease the mold temperature

# data[].attributes.body
1.Reduce the usage or amount of material.
2. control the material's viscosity.
3. Avoid overpacking the material.
4. Reduce the mold temperature.
5. Decrease the clamp pressure.
6. Reduce the clamp pressure

# data[].attributes.body
1. Increase mold temperature.
2. Extend the cycle time.
3.Slowing down the screw rotation.
4. Increase the back pressure.
5. Dry the material before use(pre-heat)
6. Increase cure time.

# data[].attributes.body
1. slowing down the screw rotation.
2. reducing the injection speed
3. increasing and optimize the mold temperature
4. increasing the back pressure
5. add breathe cycle
6. decrease mold closing speed

# data[].attributes.body
1. reduce the speed of mold closing
2. increase curing time
3. polish the mold
4. adjust mold temperature
5. check mold surface
6, increase pre heat temperature

# data[].attributes.body
1. check material viscosity
2. increase the mold temperature
3. increase the curing time
4. increase speed of mold closing
5. use high pressure
6. increase amount of material (charge)

# data[].attributes.body
1.polish the mold
2.increase preheat time
3.decrease mold closing speed
4.increase mold temperature

# data[].attributes.body
1.check parting line for wear or damage and correct as needed.
2.increase mold temperature
3.increase preheat temperature

# data[].attributes.body
1. Increase cure time
2. Slow close duration
3.Check Mold temp for uniformity
4.add breathe cycle

# data[].attributes.body
1. Reduce the mold temperature
2. reduce speed of mold closing
3. check the viscosity of material
4. reduce the clamp pressure
5. clean the mold
6. reduce the amount of material (charge

# data[].attributes.body
1. increase the breathe cycle
2. increase the curing time
3. increase the pre-heating
4. increase the mold temperature
5. do early degassing
6. reduce speed of mold closing

# data[].attributes.body
1. Increase mold temperature and pressure.
2. Increase cure time.
3. Add breathe cycle.

# data[].attributes.body
1. Increase mold or the preheat temperature.
2. Reduce the speed of the mold closing.
3. Make sure that the mold is clean and being polished.

# data[].attributes.body
1. Slow down injection rate.
2. Reduce pack/hold pressure.
3. Reduce clamp tonnage.
4. Rearrange clamp alingnment.
5. Control the viscosity of the material.
6. Clean the mold surface and inspect the cavity for proper clamping.

# data[].attributes.body
1. Use less reactive catalyst
2. Use high pressure
3. Select easier flow material (decrease charge viscosity)
4. increase charge weight
5. Increase preheat temperature
6. Increase mold temperature

# data[].attributes.body
1. Increase mold temperature
2. Increase cure cycle
3. Polish and buff tool surface
4.  Check condition of mold plating and re-plate if necessary
5.  Increase preheat temperature
6. Decrease mold closing speed

# data[].attributes.body
1. Increase preheat temperature
2. Increase cure time
3. Increase mold temperature
4. Add breathe cycle
5. Increase moulding pressure
6. Decrease mould closing speed

# data[].attributes.body
1. Decrease or reduce charge weight
2. Check parting line for wear or damage and correct as needed
3. Increase clamp tonnage if possible
4. Check material flow
5. Reduce mold temperature
6. Decrease mold closing speed

# data[].attributes.body
1. Increase charge weight
2. Increase preheat temperature
3. Increase mold closing speed
4. Decrease mold temperature
5. Check mold venting and correct as needed
6. Optimize cycle time

# data[].attributes.body
1. Decrease charge weight
2. Increase preheat temperature
3. Increase mold temperature
4. Decrease mold closing speed
5. Check parting line for wear or damage and correct as needed
6. Increase clamp tonnage if possible

# data[].attributes.body
1. Increase mold temperature
2. Increase preheat temperature
3. Decrease mold closing speed
4. Check condition of mold plating and re-plate if necessary
5. Polish mold
6. Apply mold release agent

# data[].attributes.body
1. Decrease mold closing speed
2. Add or change breathe cycle
3. Increase charge weight
4. Check mold venting and correct as needed
5. Decrease mold temperature
6. Increase hold pressure

# data[].attributes.body
1. Decrease the temperature
2. Make sure homogenous extrude of plastic
3. Apply mold release agent
4. Do not exposed to high heat
5. High melt temperature

# data[].attributes.body
1. Decrease the Clamp pressure
2. Optimize hold pressure
3. Decrease injection spEed
4. Decrease the barrel temperature
5. Reduce the clamp force

# data[].attributes.body
1. Increase hold pressure
2.increase clamping pressure
3. Increase injection speed
4. Increase screw speed
5. Optimize cycle time

# data[].attributes.body
1. Low the temperature
2. Reducing mold temperature
3. Properly drying the material
4. Need degassing to reduce bubble air trap
5. Increase the hold pressure

# data[].attributes.body
1.
2.
3.
4.
5.
6.

# data[].attributes.body
1.
2.
3.
4.
6.

# data[].attributes.body
1.
2.
3.
4
5.
6.

# data[].attributes.body
1.
2.
3.
4.
5.
6.

# data[].attributes.body
1.Increase