# data[].attributes.body
When multiplying decimals you have to line up the points

# data[].attributes.body
Keep everything lined up

# data[].attributes.body
The rules for adding, multiplying, divideding and subtracting decimals are you have to move the decimal to the right when you finish.

# data[].attributes.body
When you multiply you do it regular then you count each decimal place to the right then you add the decimal going to the left

# data[].attributes.body
When you multiply decimals you line up the decimal points then multiply like your multiplying whole numbers, then you count the numbers behind the decimal points then move the decimal point from the end

# data[].attributes.body
The rules are to line up the decimal to add, line up the numbers to multiply and the answer for division has a decimal.

# data[].attributes.body
When you are subtracting decimals and there are numbers missing just add zero to where a number should be.

# data[].attributes.body
Keep everything lined up and in order. Put the decimal in the right place. When multiply if you don’t have enough place values you have to add a zero on the end of the one that doesn’t have enough.

# data[].attributes.body
The rules of decimals is put the decimal down when you finish answering the question and put it directly below where it stood a first

# data[].attributes.body
When your dividing and you shift over the decimal to make a whole number you have to make sure you move it the same amount of times on the other number.

# data[].attributes.body
When you add or subtract decimals you have to bring a copy of the decimal into
your answer. When you multiply you need to count to the left to figure out where the decimal goes.

# data[].attributes.body
When your multiplying decimals you line the decimals up not the numbers if you line the numbers up then you won’t get the right answer.

# data[].attributes.body
Line up your decimals, remove the decimals, go from right to left , when dividing if you have two numbers like 1.5 divided by 6.43, make sure one of the decimals (the divisor in this case) is a whole number. Subtracting decimals is the same as subtracting whole numbers. Adding decimals is the same as adding whole numbers.

# data[].attributes.body
Zachary Skerrett

# data[].attributes.body
When multiplying numbers with decimals, you mentally shift the decimal to the right. When dividing, you shift the decimal on the dividend and the divisor the same amount. When adding and subtracting you line up the decimals and add a zero where there is a blank space in the number.

# data[].attributes.body
The rules are always start from right to left. Also in a multi digit number you need to add the decimals back after.

# data[].attributes.body
When subtracting decim

# data[].attributes.body
The rules for adding is so say if the number is 0.83 + 0.5 you would make the five 0.50 and then add them up. For subtracting you do the same but subtract it instead. For multiplying you have to go right to left. I forget division.

# data[].attributes.body
Forget the decimals when dividing and multiplying decimals but add them back when done, for addition and subtraction you can leave the decimal there. Add and subtract decimals just the same as whole numbers. Treat numbers with decimals like whole numbers.

# data[].attributes.body
Adding decimals. When adding decimals you line up the decimals from right to left and have them centered up so you can find the answer.

# data[].attributes.body
When your adding decimals make sure you line up the decimal so you get the right answer. B n.

# data[].attributes.body
You need to line up all your numbers then, You need to put the decimal point to the right and bring it back at the end the same amount of how many numbers were to the right of the decimal point(s).

# data[].attributes.body
When you multiply decimals, you mentally shift the decimals to the right. Then move them back to where they were when you first started. Last, count how many decimal digits there are and move it ove right that many spaces.

When adding and subtracting decimals, you have to line up the decimals. Then bring the decimal down and add or subtract like they were regular numbers.

# data[].attributes.body
When you are adding decimals you line up the decimal points and then you add.

# data[].attributes.body
The rules for adding decimals you have to line up the decimals and add the regular way for multiply you have to forget about the decimals and multiply the way you’d normally multiply then when your finished you look to the right of the decimal and you move the top number as much as there are numbers and same for the bottom and that’s how you find were to put the decimal.

# data[].attributes.body
Always have the decimals lined up
When you multiply forget the decimal and add it at the end

# data[].attributes.body
When your adding you need to put the two numbers your using andnput them together and it will be your answer