# data[].attributes.headline
Fill a graduated cylinder  and place the object 

# data[].attributes.subject
Fill a graduated cylinder  and place the object 

# data[].attributes.body
You put it in a graduated cylinder

# data[].attributes.body
You put water in a graduated cylinder and you have to put it in and you compare it to before the object went in and after than you subtract it

# data[].attributes.body
You fill a graduated cylinder with water and drop the object then record how much it went up from where you started then you find the volume

# data[].attributes.headline
First you put water into the graduated cylinder and check the volume then put the object in a check the volume agin after subtract the two

# data[].attributes.subject
First you put water into the graduated cylinder and check the volume then put the object in a check the volume agin after subtract the two

# data[].attributes.body
Fill graduated cylinder, drop object in, subtract amount now than before it was in there

# data[].attributes.body
Use a graduated cylinder then fill it water with

# data[].attributes.body
First you fill a graduated cylinder w/ water then you check the number it's at then you add the object then see the number it's at , then you subtract both

# data[].attributes.body
Fill up a graduated cylinder with a specific amount of water and then get the object you are using and drop it in the water

# data[].attributes.body
Fill up a graduated cylinder with a specific amount of water and then drop the object you are using in the water

# data[].attributes.headline
Leslie                         First, fill a graduated cylinder with water then measure how much next drop the object in the water then measure it subtract the two measurements that's the volume

# data[].attributes.subject
Leslie                         First, fill a graduated cylinder with water then measure how much next drop the object in the water then measure it subtract the two measurements that's the volume

# data[].attributes.body
Use grunted cylinder to measure volume

# data[].attributes.body
Aracely
Fill the graduated cylinder,put an object in then get the volume

# data[].attributes.body
Measure in a graduated cylinder

# data[].attributes.body
You fill a graduated cylinder w/ water then see the volume first then add the object to the water then check the volume again then subtract the first water volume th

# data[].attributes.body
First, you must fill a graduated cylinder with a specific amount of water. After, drop the object in the water. Finally, subtract the amount of water in the cylinder from the original amount.

# data[].attributes.body
Fill a graduated cylinder to a point than drop the object into the water

# data[].attributes.body
You use a graduated cylinder

# data[].attributes.body
Fist you fill a graduated cylinder with a certain amount of water then add the object and subtract the water and the object from just thewater

# data[].attributes.body
Fill a graduated cylinder with water then drop in the object. Subtract how much the water was from how much the water rose. Then you have the volume of an irregular shaped object.

# data[].attributes.body
Measure the Water in the graduated cylinder first then using water displacement drop the object inside and measure it then after that subtract the original water level and you will get you the volume of the object you can see the water level by reading the minscus

# data[].attributes.body
Fill a

# data[].attributes.body
You fill a guraduated cilinder with water then see the valume first then add the object to the water and then check the valume now

# data[].attributes.body
Fill a graduated cylinder with water then drop the object in the graduated cylinder and then calculate the difference

# data[].attributes.body
To find the volume of an irregular shaped object fill a graduated cylinder with water mark its place put the object in and see how many kilometers or other key it went up subtract the old from the new and you have an irregular shaped objects volume

# data[].attributes.body
You fill a graduated cylinder to a point then you drop the object in then caculate it

# data[].attributes.body
Fill a graduated cylinder and put the object and subtract the volume of before and after

# data[].attributes.body
Fill the graduated cylinder with water to a certain point and then you drop in the object and take the measurement and subtract the original level of water before you dropped in the object and that is your object's mass