# data[].attributes.body
Quiz 2 & Quiz 3 (PROBLEM SOLVING) - 20 mark .... each Quiz is a single question
TEST 2 (THEORY) - 15 mark (Section A True/false) & (Section B various questions, fill in the blanks, explain, state, Sketch, why, what)
Time: 2 hours
Date: 17 Dec 2019 (Tuesday), 9 - 11 am

topics:
Problem solving: surface measurement, error, Accuracy, Precision, FIT
Theory: Surface measurement, Error, Accuracy, Precision, CMM, non-contact measurement, VMM, Tolerance, Fit

# data[].attributes.body
1) Error was covered
2) Accuracy was covered

Remaining topics
Precision & Discrimination
Tolerance
Fit ....... problem solving (Table 1, 4 & 5)
GDT
Instrument Characteristics
Calibration

# data[].attributes.body
1) CMM was covered fully
2) Surface Measurement was covered fully (Profile wavelength was not taught because it is for Degree student)

# data[].attributes.body
14/11 THURSDAY: lecturer attending bengkel (5 hours Tech Dwg must replace on Sunday 2hrs 17/11 8:30 pm + on Sunday 3hrs 24/11 8:30 pm)

26/11 TUESDAY: lecturer on leave ( 2 hours instrument must replace on Sunday 2hrs 17/11 10:00 am)

# data[].attributes.body
non-contact, focus effect, lighting effect, VMM (a little was left from the main slide)

# data[].attributes.body
- finished SI, prefix, conversions with square prefixes, scientific notation, etc
- Review of Theory and Problem solving questions in class
- i didn't show them angular lab test sample

# data[].attributes.body
TEST 1 (15 marks)
Topics: SI measurement units, Linear, Angular
Section A: 11 True/False (answer 8 only): 4 marks
Section B: 4 Compulsory Questions (write, complete, label, why, what, sketch): 11 marks

Quiz 1 (10 marks)
Topics: SI measurement units, Linear, Angular
Problem Solving 10 marks: 3 questions (answer two only)

# data[].attributes.body
TEST 1: 22nd Oct (Tuesday) ... SI units, Significant numbers, linear, angular measurements

1) Sine bar was covered
2) Note Catalogs was covered
3) Significant Figure

# data[].attributes.body
1) angular measurement
2) last was discussed is bevel protractor including acute angle attachment examples
3) examples of acute angle from catalogs were not shown to students yet

# data[].attributes.body
1) Metrology Introduction Video was reviewed in class thoroughly
i. calibration of manual micrometer, digital micrometer, dial indicator
2. ratchet mechanism, lock, vernier,
3. Metrology table
2) students are required to go through the notes of linear and angular measurement

# data[].attributes.body
Assalamualaikum All

This morning class (11 am - 1 pm) will be replaced by an online activity which must be done during this class time, the activity is as follows:

1) Students must to watch this video carefully

https://youtu.be/z0G9jNk5OVQ

2) Pay attention to the caption (tulisan semasa video ditayang)

3) Note down what you understand on a piece of paper OR write it using Microsoft document which you need to submit through Kelip Submission Link entitled "Class Assignment 11th Sept (Wednesday)"

Note: activity is limited by time from 11 am to 1 pm, so please do it quickly before it is too late, the video is only 5 minutes long, so no excuse for not being able to do it

# data[].attributes.body
TEST 2 (30 marks): briefing of content and questions
Topics: CMM, Error, Accuracy, Precision, Fits, Tolerances
Theory 10 marks:
Section A (All Topics):
Section B (Bold Topics):

Section C: Problem Solving 20 marks:

# data[].attributes.body
1) Lecture Error, Accuracy & Precision was completely covered
2) Lecture Tolerances & Fits was completely covered (however, only Table 1, 4 & 5 was taught for FIT problem solving)
3) Lecture GD&T was not Covered

# data[].attributes.body
CMM theory was done successfully

# data[].attributes.body
CMM Lab session
2) Coordinate System direction rule (right hand rule)

# data[].attributes.body
TEST 1 Instrumentation was successfully done on 19th Nov 2018

# data[].attributes.body
CMM Lab session
Exp 1:
1) procedure to create origin and align axis

# data[].attributes.body
Review of TEST 1 was made (showing all past questions since 2010)
1 hour and 30 minutes was spent

# data[].attributes.body
TEST 1 (30 marks): briefing of content and questions
Topics: SI measurement units, Linear, Angular, Calibration, VMM, Instrument Selection characteristics, Surface Measurement
Theory 20 marks:
Section A (All Topics): 13 True/False (answer 10 only): 5 marks
Section B (Bold Topics): 5 Compulsory Questions (write, complete, label, why, what, sketch): 15 marks

Section C: Problem Solving 10 marks: 1 question (selected from the last topic taught)

# data[].attributes.body
1) Error, Accuracy, Precision (Lecture) ... last slide (Sheep and Cat example)

# data[].attributes.body
1) TEST after mid-sem break
2) Lecture (Surface) was covered
- sand blasting & Peening Machining videos were shown to students (machining processes that produce non-directional Lay)
3) Lecture (Calibration) was covered
4) Lecture (General Characteristics of Instrument Selection) was covered

# data[].attributes.body
1) Non-Contact Measurement (Vision Measurement Machine) was covered totally
2) Next LAB session is LAB 5 VMM: Print the sheet and bring it during the Lab session

# data[].attributes.body
Lecture about angular measurement (covered)

# data[].attributes.body
Lecture about scientific notations, prefixes, Linear measuring instrument up to vernier scale technique

# data[].attributes.body
LAB SESSION NO 1: Introduction to Linear, angular, CMM and VMM measurement machines

# data[].attributes.body
Today's Class (17/9/18):
1) Measurement Systems Lecture
2) Base and Derived units (not yet into scientific notation)
3) SI document was covered

Note: Monday's Lecture will be as it is starting at 4 pm to 6.20 pm. Dr Siti wants to conduct LAB after 2 pm.

# data[].attributes.body
Lecture Introduction ,Metrology videos and DCI were covered...

On Tuesday 18 Sept, 16 students attend LAB at 11-1pm, another 16 will attend the LAB at 2-4pm

# data[].attributes.body
ONLINE COURSE: Measurement Uncertainty
http://www.npl.co.uk/upload/pdf/intro-meas-uncert-flyer.pdf
http://www.npl.co.uk/commercial-services/products-and-services/training/e-learning/measurement-explained-series/

# data[].attributes.body
ISO STANDARDS FOR METROLOGY
https://www.iso.org/ics/17/x/

# data[].attributes.body
UK GUIDE
http://www.npl.co.uk/publications/guides/

# data[].attributes.body
Hadith Narrated by Imam Muslim