# data[].attributes.body
A breadboard is a construction base for prototyping of electronics

# data[].attributes.body
a device converting solar radiation into electricity.

# data[].attributes.body
A combination circuit is one that has a "combination" of series and parallel paths for the electricity to flow. Its properties are a combination of the two. In this example, the parallel section of the circuit is like a sub-circuit and actually is part of an over-all series circuit.

# data[].attributes.body
denoting electrical circuits or components arranged so that the current passes through each successively.

# data[].attributes.body
Semiconductor-based temperature sensors, or integrated circuit (IC) temperature sensors, operate with reverse bias, have a small capacitance and a low leakage current. They are formed on thin wafers of silicon. They are compact, produce linear outputs, and have a small range of temperature.

# data[].attributes.body
A rechargeable battery, storage battery, or secondary cell, (or archaically accumulator) is a type of electrical battery which can be charged, discharged into a load, and recharged many times, as opposed to a disposable or primary battery, which is supplied fully charged and discarded after use.

# data[].attributes.body
An electronic symbol is a pictogram used to represent various electrical and electronic devices or functions, such as wires, batteries, resistors, and transistors, in a schematic diagram of an electrical or electronic circuit.

# data[].attributes.body
A schematic diagram is a picture that represents the components of a process, device, or other object using abstract, often standardized symbols and lines. Although schematic diagrams are commonly associated with electrical circuits, many examples can be found in other industries.

# data[].attributes.body
a device having a designed resistance to the passage of an electric current.

# data[].attributes.body
the degree to which a substance or device opposes the passage of an electric current, causing energy dissipation. Ohm's law resistance (measured in ohms) is equal to the voltage divided by the current.

# data[].attributes.body
a stable subatomic particle occurring in all atomic nuclei, with a positive electric charge equal in magnitude to that of an electron, but of opposite sign.

# data[].attributes.body
an electric cell that produces current by an irreversible chemical reaction.

# data[].attributes.body
energy that is produced by mechanical, electrical, or other means and used to operate a device.

# data[].attributes.body
Polarity in a Parallel Circuit. Just as in series circuits, electrical current flows “from negative to positive” through each of the load components in a parallel circuit.

# data[].attributes.body
a device for viewing oscillations, as of electrical voltage or current, by a display on the screen of a cathode ray tube.

# data[].attributes.body
a law stating that electric current is proportional to voltage and inversely proportional to resistance.

# data[].attributes.body
An ohmmeter is an electrical instrument that measures electrical resistance (the opposition offered by a substance to the flow of electric current) . ... The unit of measurement for resistance is ohms (Ω).

# data[].attributes.body
a subatomic particle of about the same mass as a proton but without an electric charge, present in all atomic nuclei except those of ordinary hydrogen.

# data[].attributes.body
a machine, especially one powered by electricity or internal combustion, that supplies motive power for a vehicle or for some other device with moving parts.

# data[].attributes.body
For application to area lighting, see LED lamp. Not to be confused with LCD. semiconductor light source.

# data[].attributes.body
an atom or molecule with a net electric charge due to the loss or gain of one or more electrons.

# data[].attributes.body
an electronic circuit formed on a small piece of semiconducting material, performing the same function as a larger circuit made from discrete components.

# data[].attributes.body
a substance or device which does not readily conduct electricity.

# data[].attributes.headline
Institute of Electrical and Electronics Engineers (IEEE) 

# data[].attributes.subject
Institute of Electrical and Electronics Engineers (IEEE) 

# data[].attributes.body
The Institute of Electrical and Electronics Engineers is a professional association for electronic engineering and electrical engineering with its corporate office in New York City and its operations center in Piscataway, New Jersey.

# data[].attributes.body
An incandescent light bulb, incandescent lamp or incandescent light globe is an electric light with a wire filament heated until it glows. The filament is enclosed in a bulb to protect the filament from oxidation. Current is supplied to the filament by terminals or wires embedded in the glass.

# data[].attributes.body
a car with a gasoline engine and an electric motor, each of which can propel it.

# data[].attributes.body
a dynamo or similar machine for converting mechanical energy into electricity.

# data[].attributes.body
Gas-discharge lamps are a family of artificial light sources that generate light by sending an electric discharge through an ionized gas, a plasma.

# data[].attributes.body
A fluorescent lamp, or fluorescent tube, is a low-pressure mercury-vapor gas-discharge lamp that uses fluorescence to produce visible light.

# data[].attributes.body
a stable subatomic particle with a charge of negative electricity, found in all atoms and acting as the primary carrier of electricity in solids.

# data[].attributes.body
a conductor through which electricity enters or leaves an object, substance, or region.

# data[].attributes.body
a form of energy resulting from the existence of charged particles (such as electrons or protons), either statically as an accumulation of charge or dynamically as a current.

# data[].attributes.body
It is the branch of engineering that deals with the technology of electricity. Electrical engineers work on a wide range of components, devices and systems, from tiny microchips to huge power station generators.

# data[].attributes.body
an electric current flowing in one direction only.

# data[].attributes.body
a semiconductor device with two terminals, typically allowing the flow of current in one direction only.

# data[].attributes.body
a flow of electricity which results from the ordered directional movement of electrically charged particles.

# data[].attributes.body
the SI unit of electric charge, equal to the quantity of electricity conveyed in one second by a current of one ampere.

# data[].attributes.body
A continuity tester is an item of electrical test equipment used to determine if an electrical path can be established between two points; that is if an electrical circuit can be made. The circuit under test is completely de-energized prior to connecting the apparatus.

# data[].attributes.body
a material or device that conducts or transmits heat, electricity, or sound, especially when regarded in terms of its capacity to do this.

# data[].attributes.body
A compact fluorescent lamp (CFL), also called compact fluorescent light, energy-saving light and compact fluorescent tube, is a fluorescent lamp designed to replace an incandescent light bulb; some types fit into light fixtures designed for incandescent bulbs.

# data[].attributes.body
a thin rigid board containing an electric circuit; a printed circuit.

# data[].attributes.body
a device containing electrodes immersed in an electrolyte, used for current-generation or electrolysis.

# data[].attributes.body
a device used to store an electric charge, consisting of one or more pairs of conductors separated by an insulator.

# data[].attributes.body
a container consisting of one or more cells, in which chemical energy is converted into electricity and used as a source of power.

# data[].attributes.body
the basic unit of a chemical element.

# data[].attributes.body
An ammeter (from Ampere Meter) is a measuring instrument used to measure the current in a circuit.

# data[].attributes.body
The common standard for the diameter (gauge) of round drawn wire is the American Wire Gauge (AWG).

# data[].attributes.body
an electric current that reverses its direction many times a second at regular intervals, typically used in power supplies.

# data[].attributes.body
The simplest type of bridge used to span the shortest distance.

# data[].attributes.body
The structural member that carries horizontal loads.

# data[].attributes.body
A type of bridge that relies on the strength and rigidity of the arch. The strength of an arch is that the structural members are always in compression and that it can distribute the load throughout the arch to the abutments.

# data[].attributes.body
The structural component that connects the bridge to the ground at the ends of the bridge.

# data[].attributes.body
the ratio of the force produced by a machine to the force applied to it, used in assessing the performance of a machine.

# data[].attributes.body
Linear motion (also called rectilinear motion) is a one-dimensional motion along a straight line, and can therefore be described mathematically using only one spatial dimension.

# data[].attributes.body
a rigid bar resting on a pivot, used to help move a heavy or firmly fixed load with one end when pressure is applied to the other.

# data[].attributes.body
energy which a body possesses by virtue of being in motion.

# data[].attributes.body
a unit of power equal to 550 foot-pounds per second (745.7 watts).

# data[].attributes.body
A hydraulic system is a drive technology where a fluid is used to move the energy from e.g. an electric motor to an actuator, such as a hydraulic cylinder.

# data[].attributes.body
(in a gearbox, transmission, etc.) the ratio between the rates at which the last and first gears rotate.

# data[].attributes.body
The resistance that one surface or object encounters when moving over another.

# data[].attributes.body
The measure of the result of pressurized fluid acting upon a chamber in a fluid power system.

# data[].attributes.body
Rollers and balls placed between moving parts to reduce friction and wear.

# data[].attributes.body
A device for converting hydraulic energy into mechanical energy, i.e., a motor or cylinder.

# data[].attributes.body
is a view of an object as it would be seen by an observer who looks at the object either in a chosen direction or from a selected point of view. •Pictorial drawings often are more readily made and more clearly understood than are front, top, and side views of an object.

# data[].attributes.body
common method of representing three-dimensional objects, usually by three two-dimensional drawings in each of which the object is viewed along parallel lines that are perpendicular to the plane of the drawing.

# data[].attributes.body
In technical drawing and computer graphics, amultiview projection is a technique of illustration by which a standardized series of orthographic two-dimensional pictures is constructed to represent the form of a three-dimensional object.

# data[].attributes.body
is the process of developing a mathematical representation of any three-dimensionalsurface of an object (either inanimate or living) via specialized software.

# data[].attributes.body
a drawing to scale of a machine, machine component, architectural plan, etc, from which dimensions can be taken for manufacture.

# data[].attributes.body
also known as idea generation, is the creative process of developing ideas. Start ideation after you have settled on a design problem that you want to solve and have done your background research, including the analysis of existing solutions.

# data[].attributes.body
is a book in which anengineer will formally document, in chronological order, all of his/her work that is associated with a specific design project.

# data[].attributes.body
is the process of devising a system, component, or process to meet desired needs.

# data[].attributes.body
contains the key points to enable the manufacture or description of a single component that defines and communicates part of a complete design to other interested parties.

# data[].attributes.body
is a method for generating ideas to solve a design problem. It usually involves a group, under the direction of a facilitator.

# data[].attributes.body
is a method for automating control of machine tools through the use of software embedded in a microcomputer attached to the tool.

# data[].attributes.body
is a computer technology that designs a product and documents the design's process. CAD may facilitate the manufacturing process by transferring detailed diagrams of a product's materials, processes, tolerances and dimensions with specific conventions for the product in question.

# data[].attributes.body
the use of a computer to represent the dynamic responses of one system by the behaviour of another system modeled after it. A simulation uses a mathematical description, or model, of a real system in the form of a computer program.

# data[].attributes.body
To do this, engineers often use a technique called "brainstorming." Brainstorming is a team creativity activity that helps you generate a large number of potential solutions to a problem or challenge.

# data[].attributes.body
is the effect an organization's actions have on the well being of the community.

# data[].attributes.body
is the science of risks and their probability and evaluation. Probabilistic risk assessment is oneanalysis strategy usually employed in science andengineering.

# data[].attributes.body
“an individual, who has fulfilled education and experience requirements and passed rigorous exams that, under State licensure laws, permits them to offer engineering services directly to the public.

# data[].attributes.body
It is a breakthrough in the world.

# data[].attributes.body
A patent engineer or patent scientist is apatent professional who is typically involved in preparing and prosecuting patentapplications.

# data[].attributes.body
Experiments in genetic engineering can be extremely dangerous, life-threatening, mutating, and have horrifying consequences.

# data[].attributes.body
approaches the design of products and processes by applying financially and technologically feasible principles to achieve one or more of the following goals: (1) decrease in the amount of pollutionthat is generated by a construction or operation of a facility, (2) minimization of human population exposure to potential hazards (including reducing toxicity, (3) improved uses of matter and energy throughout the life cycle of the product and processes, and (4) maintaining economic efficiency and viability.[1] Green engineering can an overarching framework for all design disciplines.

# data[].attributes.body
Is the field of system of moral principles that apply to the practice of engineering. The field examines and sets the obligations by engineers to society, to their clients, and to the profession.

# data[].attributes.body
Is defined as any change to the environment, whether adverse or beneficial, wholly or partially resulting from an organization's activities, products, or services. From: Subsea Pipeline Integrity and Risk Management, 2014.

# data[].attributes.body
An economic impact analysis (EIA) examines the effect of an event on the economy in a specified area, ranging from a single neighborhood to the entire globe. It usually measures changes in business revenue, business profits, personal wages, and/or jobs.

# data[].attributes.body
is the field of system of moral principles that apply to the practice of engineering. The field examines and sets the obligations by engineers to society, to their clients, and to the profession.

# data[].attributes.body
Is a non-governmental organization that accredits post-secondary education programs in applied and natural science, computing, engineering and engineering technology.

# data[].attributes.body
is a situational decision that involves diminishing or losing one quality, quantity or property of a set or design in return for gains in other aspects. In simple terms, a tradeoff is where one thing increases and another must decrease.

# data[].attributes.body
is the subject which uses optimization techniques to achieve design goals in engineering.

# data[].attributes.body
Is the subject which uses optimization techniques to achieve design goals in engineering.

# data[].attributes.body
Conditions that we need to happen or would like to happen with a design.

# data[].attributes.body
The engineering design process is a series of steps that engineers follow to come up with a solution to a problem.