# data[].attributes.body
Rock woo

# data[].attributes.body
On a flat roo

# data[].attributes.body
Specification drawings

# data[].attributes.body
Layout drawing

# data[].attributes.body
Socrative room name is Nzilskqt if your interested 💩💩💩💩💩

# data[].attributes.body
Adam has tinder premium

# data[].attributes.body
Building Regs

# data[].attributes.body
A work method statement, sometimes referred to as a safe work method statement or SWMS or a safe work procedure, is a part of a workplace safety plan.

# data[].attributes.body
Fibre glass is made from recycled materials

# data[].attributes.body
A mist coat is made of watered down paint and applied in a thin layer. You should put a mist coat of paint on new plaster on your walls to seal it and prevent peeling.[1] Start by preparing the mist coat so it has the right ratio of water and paint. Then, apply it evenly to your walls and let it dry. You can then apply a top coat over the mist coat without having to worry about creases or cracks in the paint. it is 50 percent water and 50 percent paint

# data[].attributes.body
A site plan is an architectural plan, landscape architecture document, and a detailed engineering drawing of proposed improvements to a given lot. A site plan usually shows a building footprint, travelways, parking, drainage facilities, sanitary sewer lines, water lines, trails, lighting, and landscaping and garden elements.[1]

Such a plan of a site is a "graphic representation of the arrangement of buildings, parking, drives, landscaping and any other structure that is part of a development project".[2]

A site plan is a "set of construction drawings that a builder or contractor uses to make improvements to a property. Counties can use the site plan to verify that development codes are being met and as a historical resource. Site plans are often prepared by a design consultant who must be either a licensed engineer, architect, landscape architect or land surveyor

# data[].attributes.body
https://

# data[].attributes.body
A temporary benchmark (TBM) is a fixed point with a known elevation used for level control during construction works and surveys. Nails in road seals, or marks on kerb & channel are commonly used as temporary benchmarks.

# data[].attributes.body
Risk assessment is the determination of quantitative or qualitative estimate of risk related to a well-defined situation and a recognized threat (also called hazard). Quantitative risk assessment requires calculations of two components of risk(R): the magnitude of the potential loss (L), and the probability (p) that the loss will occur.

# data[].attributes.body
Programmes describe the sequence in which tasks must be carried out so that a project (or part of a project) can be completed on time.

# data[].attributes.body
3-4-5 Method

# data[].attributes.body
A concrete mixture ratio of 1 part cement, 3 partssand, and 3 parts aggregate will produce a concrete mix of approximately 3000 psi. Mixing water with the cement, sand, and stone will form a paste that will bind the materials together until the mix hardens.

# data[].attributes.attachment_link.description
A short video using computer modelling to explain the general structural principles of domestic timber roofing.

# data[].attributes.headline
ordinary Portland cement is the most commonly used cement in construction and it also binds the mix together  

# data[].attributes.subject
ordinary Portland cement is the most commonly used cement in construction and it also binds the mix together  

# data[].attributes.body
fine aggragate are basically sands won from the land or the marine environment. Fine aggregatesgenerally consist of natural sand or crushed stone with most particles passing through a 9.5mm sieve. As with coarse aggregates these can be from Primary, Secondary or Recycled sources

# data[].attributes.body
The most common types of materials used for loose-fill insulation include cellulose, fiberglass, and mineral (rock or slag) wool. ... Cellulose is primarily made from recycled newsprint. Most fiberglass contains 20% to 30% recycled glass.

Fiberglass. Fiberglass Insulation. Fiberglass is the most common insulation used in modern times. ...

Mineral Wool. Mineral Wool. ...

Cellulose. Cellulose Insulation Material. ...

Polyurethane Foam. Polyurethane Insulation. ...

Polystyrene. Polystyrene (Styrofoam).

# data[].attributes.headline
coarse aggregate are loose chippings from demolished  buildings 

# data[].attributes.subject
coarse aggregate are loose chippings from demolished  buildings 

# data[].attributes.body
The site plan (also known as a block plan) should be drawn at an identified standard metric scale (typically 1:100, 1:200 or 1:500). It should show the proposed development in relation to the site boundaries and other existing buildings on the site, with dimensions specified including those to the boundaries.

# data[].attributes.body
Strip foundations are used where the soil is of good bearing capacity. The key sizes of a strip foundationfor concrete cavity wall construction and timber frame cavity wall construction are similar. The size and position of the strip is directly related to the overall width of the wall.

# data[].attributes.headline
pile foundation used on large buildings such as a college or multi storey car park to hold the weight 

# data[].attributes.subject
pile foundation used on large buildings such as a college or multi storey car park to hold the weight 

# data[].attributes.headline
a point which serves as a reference or base fort the measurement of other quantities 

# data[].attributes.subject
a point which serves as a reference or base fort the measurement of other quantities 

# data[].attributes.body
A damp proof membrane (DPM) is a barrier through the structure designed to prevent moisture rising by capillary action such as through a phenomenon known as rising damp

# data[].attributes.headline
a section drawing shows a view of the structure that you are building

# data[].attributes.subject
a section drawing shows a view of the structure that you are building

# data[].attributes.body
construction hatchings are used as symbols on plans and drawings

# data[].attributes.body
one skin blocks and one skin bricks with red wall ties to hold the walls together with insulation added