# data[].attributes.headline
The project itself had no specific significance, so I just wanted to make something that I thought would look cool. My first attempt at this project unfortunately dried up and broke apart, so I had to remake the entire project which ended up working out because i'm much more satisfied with the way my second attempt at the project turned out.

# data[].attributes.subject
The project itself had no specific significance, so I just wanted to make something that I thought would look cool. My first attempt at this project unfortunately dried up and broke apart, so I had to remake the entire project which ended up working out because i'm much more satisfied with the way my second attempt at the project turned out.

# data[].attributes.headline
I made even square outlines on a slab of clay by tracing them with a wooden stick

# data[].attributes.subject
I made even square outlines on a slab of clay by tracing them with a wooden stick

# data[].attributes.headline
Then I divided the squares one way also with the wooden stick to turn them into rectangles

# data[].attributes.subject
Then I divided the squares one way also with the wooden stick to turn them into rectangles

# data[].attributes.headline
After I had a desirable amount of rectangle slabs I then stacked them up to a 12 inch long tower

# data[].attributes.subject
After I had a desirable amount of rectangle slabs I then stacked them up to a 12 inch long tower

# data[].attributes.headline
The project began to go wrong when I took it home during thanksgiving break. The slabs slightly dried up and I tried my best to revive them but unfortunately it ended up crumbling in the end.

# data[].attributes.subject
The project began to go wrong when I took it home during thanksgiving break. The slabs slightly dried up and I tried my best to revive them but unfortunately it ended up crumbling in the end.

# data[].attributes.body
(trying to make the slabs damp again by soaking them in water)

# data[].attributes.body
On top of it being dry, I also slipped and scorer incorrectly which made things even worse in the end

# data[].attributes.headline
After the break I decided it was best just to recycle my project and start from scratch. So then I rolled out more slabs and decided to try to take 3 long slabs and spiral them on a large pipe.

# data[].attributes.subject
After the break I decided it was best just to recycle my project and start from scratch. So then I rolled out more slabs and decided to try to take 3 long slabs and spiral them on a large pipe.

# data[].attributes.headline
To keep the clay on the pipe while it got leathered, I pinched the ends of the slab on to the end of the pipe.

# data[].attributes.subject
To keep the clay on the pipe while it got leathered, I pinched the ends of the slab on to the end of the pipe.

# data[].attributes.headline
Then I cut off the ends of the slabs on the pipe so it was flat and made more slabs to keep the spiral intact once it was off the pipe

# data[].attributes.subject
Then I cut off the ends of the slabs on the pipe so it was flat and made more slabs to keep the spiral intact once it was off the pipe

# data[].attributes.headline
I made sure to slip and score correctly this time and it ended up sticking to the slabs nicely

# data[].attributes.subject
I made sure to slip and score correctly this time and it ended up sticking to the slabs nicely

# data[].attributes.headline
Although tedious, I carefully took the clay off of the pipe and put a plastic bag under it just in case it were to stick to the pipe when I wanted to take it off.

# data[].attributes.subject
Although tedious, I carefully took the clay off of the pipe and put a plastic bag under it just in case it were to stick to the pipe when I wanted to take it off.

# data[].attributes.headline
After it dried a little bit more I took it off of the pipe and it stayed intact

# data[].attributes.subject
After it dried a little bit more I took it off of the pipe and it stayed intact

# data[].attributes.headline
Finally, I took a wet sponge and cleaned up the outside and then I was finished.

# data[].attributes.subject
Finally, I took a wet sponge and cleaned up the outside and then I was finished.