# data[].attributes.body
When you have stuck your wood together you will need to get another piece of wood and stick it on and also you will need to get a straw and carefully cut it into 3 parts.

# data[].attributes.body
once you have all your pieces you will need to set them out and then glue them together.i would recommend using a glove so you dont get burnt.if you are a child you should be supervised with the glue gun.

# data[].attributes.body
Secondly you need to acuratelly measure you'r pieces of wood with a pencil then chop it with a hand saw and a wooden block before hot glueing the freshly cut pieces together carefully!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

# data[].attributes.body
Secondly we cut all the pieces of wood to the size we wanted.

# data[].attributes.body
First plan your roman catapult,measure the wood  and cut it then stick it together with a glue gun.

# data[].attributes.body
first

# data[].attributes.body
firstly you will need to plan and design your catapult with a piece of paper and a pencil.preferable a5.to help you can put the measurements on the piece of paper.you might need a white board to help you.

# data[].attributes.body
6.put a thick glove on and get a hot glue gun plug it in and use a little bit of hot glue on the conners.

# data[].attributes.body
Firstly you design you catapult.
Next get the stuff you need this is the list.
.wood
.milk bottle lid
.hand saw
. hot glue gun
.white card
. elastic band
. pins
That's what you need.

# data[].attributes.body
then you need to use the hot glue gun, (only use one drop)to stick the wood together WARNING DO NOT FORGET TO BE SAFE (that includes not getting burnt. )Always put your gloves on!!!

# data[].attributes.body
Firstly you need to plan and design your catapult.
When you get to the glue gun make sure you have gloves on and be careful.

When you have finished the base you need to get the fireing arm it needs to be bigger than the top of the base.

# data[].attributes.body
Lastly we carefully stuck a milk bottle lid on the piece of wood by using a hot glue gun.

# data[].attributes.body
After you have made the frame you need to get a milk bottle top, elastic band, a straw and some pins.  Using a glue gun stick the bottle top on a piece of wood and put the elastic band across it securing it with a pin.  when your finished place pins in the corners so it doesn't fall apart.

# data[].attributes.body
secondly  you need to  start  putting   it in place  . Then  put  some hot glue on the ends   to hold it in place  next measure  some  wood  for the   catapult  .  finally  we hot glue  a  bottle  lid  to the wood. After that you need to attach the wood to the catapult.

# data[].attributes.body
firstly you need to plan and design your catapult,But you need to rember to measure
so you know how long it needs to be. Next you need to saw your pesic of wood to the right length.

# data[].attributes.body
Firstly you need plan and design your Roman catapult.After measure the wood,mark on the wood with pencil how long the piece of wood will be. Next get a hand saw and cut where you marked on the wood.

# data[].attributes.body
Finally put in 3 drawing pins and atatch an elastic band and paint black or brown. T ADA you are done but only pull it back and try it out when the hot glue is fully dry or it could fall apart. When it is finally dry then BOMBS AWAY! If you hit someone then either reatreat or PARTY!!!!!!!!!!!!

# data[].attributes.body
fist you need to plan the catapult,you will need to measure the length of the wood

# data[].attributes.body
firstly you need to plan and design your catapult. next you get your wood and measure the wood out. Then you make the bottom  layer of the catapult then you saw the wood to make it stand.

# data[].attributes.body
Finally you need to get some elastic
bands/drawing pins.And atatch them to the catapult.TADA!!!
BOM'S AWAY!!! You have made your catapult!Now you are fineshed.

# data[].attributes.body
First you need to plan and design your catapult.