# data[].attributes.body
slope is the rate of change and y intercept is the starting point or where the line crosses

# data[].attributes.body
Slope measures the steepness of a line.If the line falls to the right its positive. If the line falls to the left its negative. If the line is horizontal its slope is 0.
Y intercept is where the line hits the Y axis on a graph

# data[].attributes.body
slope is a rise over run and a y-int is a (o,#)

# data[].attributes.body
is the rate of change and y intercept is the starting point or were the line crosses

# data[].attributes.body
the slope measures the steepness of the line so n this equation -2x would be the slope and 4 would be the y-intercept because it the first number like your starting point.

# data[].attributes.body
Slope is rise /run y intercept is where the line crosses the y axis b

# data[].attributes.body
slope is the rate of change

# data[].attributes.body
slope is the horizontal line at can be flat, vertical, going up, going down. Y intercept is represented as B

# data[].attributes.body
The slope of the problem is -2x and the y- intercept is 4. The slope is m and the y- intercept is b.  You could find the slope by using y2-y1 over x2-x1.

# data[].attributes.body
the slope of this equation is -2x which is the steepness of the line .the y-intercept or the starting point is 4.

# data[].attributes.body
Slope measures the steepness of a line.

# data[].attributes.body
the slope is -2x and the y int is 4  the slope is always M and the y int is B

# data[].attributes.body
The slope of the equation is -2 and the y-int is 4. The slope is always m and the y int is always b

# data[].attributes.body
slope measures the steepness of a line on a graph. Slope can be found by doing the equation
y2-y1 over x1-x2. in the equation y=mx+b the slope is the mx and the y-intercept is is the b. slope is the rate of change and y-intercept is the starting point

# data[].attributes.body
The slope of the equation is -2x and the y-intecept is 4.The slope is also known from the rate of change.This tells you how steep your line is.The slope uses change in y over change in x.There are also four outcomes of sloe thy are negitive ,positive, undenfined,and fla.also the y intercept is the starting point

# data[].attributes.body
The slope is the m of the equation. When the line is horizontal on the graph the slope is 0. When the line is vertical it is undefined, no slope. When the slope is less than 1 it either goes up or down a hill, depends on if the slope is positive or negative. When the slope is greater than 1 it either goes up or down a mountain, depends on if the slope is positive or negative.
The y-intercept is the b of the equation. Its the starting point of the graph. The coordinates of it would be (0,#). It is located where the line crosses the y-axis

# data[].attributes.body
y-intercept is most the smaller numbers, that where lines cross

# data[].attributes.body
The slope of the equation is -2x and the y-intercept is 4. The slope is the rate of change. It tells the steepness of your line. The slope is always has the x on the end in y=mx+b. The slope uses change in y over change in x. It also uses y2-y1 over x2-x1. There are 4 different outcomes of slope names negative, posotive, undefined, and flat. Now the y-intercept. The y-intercept in the starting poing. We also use (0,y-int). The y-intercept in that last equation is replaced by a numebr. The y-intercept is the b in y=mx+b.

# data[].attributes.headline
Slope measures steepness of a line.  Using the equation  y = -2x +4, explain the concepts of slope and y intercept.

# data[].attributes.subject
Slope measures steepness of a line.  Using the equation  y = -2x +4, explain the concepts of slope and y intercept.