# data[].attributes.body
the first step is we roll a marble down the ramp, the second is that the marble hits a cup and the cup falls, the third one is the cup lands on dominoes, the fourth is the dominoes hit jenga blocks, the fifth is that the jenga hits the hammer, he sixth is the hammer hits a book, the seventh is the book hits a binder, the eighth is the binder hits the stapler. we were able to get all of the steps working most of the time but the book would sometimes fall over. The most challenging step to make was the dominoes since they kept falling over when we would set them up. If i were to change one thing it would be the one with the jenga cause i think it would be better if we changed it up a little more.

# data[].attributes.body
Our movie is based on a guy who dreams of being a famous rapper, but gets a viral you tube video of him and his brother fighting instead. I think that our movie was good because it reached all of our expectations. If I had to change one thing it would probably be the quality of the green screen.

Unable to add movie clip (hutch is sick)

# data[].attributes.body
Our game is based on Peppa the pig trying to get through all of Mr potatoes rides. Our game turned out good, If I could change one thing I would the way the levels change cause with a jet pack you can flu over all of the levels.

# data[].attributes.body
We were told to create a device that releases a specific amount of candy. We used a shoe box to create out build we also used lots of rubber bands and sticks to make the hing go down on command. It worked, I think it worked because we did many tests and if we messed up we would destroy it all and fix the entire thing.

# data[].attributes.body
We were told to make a pinball machine that allows us to play pinball in a fun way. Our theme for our pinball machine is PEPPA PIG, it has all the family as obstacles and there car, we have flippers and a marble despenser that is in peppa´s mouth. I like the design and how everything looks the most out of everything. The thing I think we can approve on is the flippers because they are hard to swing to hit the marble.

# data[].attributes.body
this is our pinball machine.

# data[].attributes.body
We were told to make a device using scratch that makes a sound using coding. Our device is a guitar that plays songs. Our device worked well. I think it worked because we did a good job coding and making the guitar

# data[].attributes.body
We were told to make a boat that will hold 40 g of pennies and travel 20 in. our boat held the pennies but did not travel all 12 in. Our prototype did not work cause we had to remake it since it broke and even that one broke. Next time I think we should add more protection to the boat.

this is our boat

# data[].attributes.body
this our data sheet

# data[].attributes.body
We were told to create a bridge that can hold 5 pounds of sand only made out of pasta. We tested our prototype by putting it on the river to see the length and how it bent with the bucket. Our bridge Worked and it held 5.6 pounds of sand and I think it worked because we had a lot of top support and a sturdy bottom.

this is our bridge

# data[].attributes.body
We were told to make a device that will protect an egg from cracking when being dropped of the football stands. we tested our device by dropping it off the table a couple times so we do not damage it since it was made completely out of straws. our device failed the challenged cause our device was very weak and the egg slid out of the device. Next time we should add more support to the egg so it does not fall out.

This is what our device looked like.

# data[].attributes.body
We were told to create a catapult that can shoot a ping pong ball into shoe box. We tested the catapult by aiming it toward the shoe box and if it did not go far enough we would add more force and if it was shooting to far to one side we would turn the catapult and for the test to see if we could make 8/10 shots we got 0/10. Our prototype did not work cause our rubber band kept turning so we had to shoot our catapult sideways. We could try to make our catapult more clean and make sure that our rubber band is not bending the catapult.

# data[].attributes.body
this is our data sheet