# data[].attributes.body
roughly five in. tall lidded form. It has a hole drilled in the top to add a little pice of twine after firing.

# data[].attributes.body
A lidded form that has the piano sheet music for the song Ophelia carved around the outside of it.

# data[].attributes.body
Still needs to have the sheet music carved into the lid.

# data[].attributes.body
7in diameter with groves carved in to lay chopsticks across the top

# data[].attributes.body
I caved and made an udon bowl

# data[].attributes.body
Trimmed foot of the bowl

# data[].attributes.body
6in in diameter this bowl has a simple lip alteration and a carving on the inside mimicking a leaf like fossil.

# data[].attributes.body
the foot of the bowl

# data[].attributes.body
A small 5in tall vase with groves carved into the bottom half

# data[].attributes.body
the foot

# data[].attributes.body
Another side

# data[].attributes.body
Another side

# data[].attributes.body
The vase features three different carving patterns. Two of which are symbols of characters and the third being a sun like patterns

# data[].attributes.body
Another side

# data[].attributes.body
The lid for the lidded form

# data[].attributes.body
It’s a shell like carving into it.

# data[].attributes.body
The first try dried out. This second try is 7in tall and still requires to be trimmed.

# data[].attributes.body
The first try dried out. This vase is 6in tall.

# data[].attributes.body
the other side.

# data[].attributes.body
another side

# data[].attributes.body
carved grooves into the mushroom caps, on both the inside and outside of the caps

# data[].attributes.body
Mushrooms have been added to all sides

# data[].attributes.body
added the first two mushrooms as well as did some scraping into the handle to give it more of a bark like look.

# data[].attributes.body
roughly 7in tall with a 6in diameter

# data[].attributes.body
A bowl that is 6in in diameter featuring a branch and bird carving on the outside.

# data[].attributes.body
started off with a 6in tall bulb like form and a then removed parts of it to make an almost leaf like pattern. Then Carved in a unique pattern into each of the six petals.

# data[].attributes.body
The original closed form

# data[].attributes.body
Another shot of the first success

# data[].attributes.body
5 1/2 inch tall candle lamp shade. This was the 8th attempt at throwing a closed form. After being thrown I pierced a star and moon pattern into it.

# data[].attributes.body
10 inch tall bottle form!

# data[].attributes.body
Another 7 inch tall bottle, but this one is slightly wider at the bottom than the first try.

# data[].attributes.body
First attempt at a bottle form. It's 7 inches tall

# data[].attributes.body
bottom view

# data[].attributes.body
8in tall vase, with a 6in diameter. There is a flower pattern carved on it. And there is a lip alteration to it.

# data[].attributes.body
6in tall vase, with a 5in diameter. There is a wave pattern carved into it.

# data[].attributes.body
Bottom view of the first try

# data[].attributes.body
Here's a full turn around video! (I hope this works....)

# data[].attributes.body
Bottom view of the second try.

# data[].attributes.body
This second planter is the same size as the first (6" diameter with 5" height) but with a twist. This planter is meant for orchid plants and has a leaf like pattern carved around it.

# data[].attributes.body
Bottom View of the first try planter.

# data[].attributes.body
Side view of the first try plater.

# data[].attributes.body
Top view of my first planter. This one is just a standard planter. It has a 6" diameter and it is 5" tall.

# data[].attributes.body
For my second platter I wanted to try something a little bit different. Inspired by a plater I saw on pinterest, this platter has the lip folded over where two cups sit. Each cup roughly 3.5 inches in diameter.

# data[].attributes.body
The bottom view of the second chip and dip platter. This one is slightly smaller with an 11 inch diameter.

# data[].attributes.body
Top view of the first chip and dip platter I completed. The cup has a 4 inch diameter and the whole platter has a 12 inch diameter.

# data[].attributes.body
My first attempt. The platter was fine till I finished and left it in the garage where it suffered a fatal blow and cracked.