# data[].attributes.body
Name: Azfar

Creativity: Uses a servo to release a rubber band which activates the slider to launch the plane. The slider is essential for not destroying the plane on release while allowing it to fly the correct distance.

Highlight: When our robot tipped over at qualifiers.

Quote: "The robot is roboting" -Gavin, rookie builder

# data[].attributes.attachment_caption
A pic of our bot holding a rose before an outreach event at a nursing home. 

# data[].attributes.body
Name: Beefcake

Creativity: The robots' arm is mostly 3D printed and is powered by two servos input into custom servo boxes that increase arm torque to decrease stress on the servos.

Highlight: Getting called a corpse when the bot would not move from the referee.

Quote: "He's just bulking I swear" -Aayan, Captain of RISE

# data[].attributes.body
Name: Beka

Creativity: Our innovative idea is the "swing" system on the outtake, this allows us to save space and slot for one servo by releasing pixels one at a time with this system.

Highlight: This robot won all qual matches solo (alliance robot was AFK)

Quote: "If it ain't broke - don't fix it" - Sergey, captain

# data[].attributes.attachment_caption
A side view of our robots claw and hanging mechanism. 

# data[].attributes.body
Name: Bartholomunchkinrrr

Creativity: Uses a servo to lift our shower hook, and the hook disconnects after it grabs the bar. We attached strong magnets to the hook so that it can stay in place during the match, but it is still able to disconnect easily.

Highlight: When our claw broke off on our first match

Quote: "One of the robots of all time" -Shane, head builder

# data[].attributes.attachment_caption
A hook in a partially extended position. 

# data[].attributes.body
Name: Pizza Bot

Creativity: Uses chain to mechanically lift hook as linear actuator extends, allowing it to stay below 14 inches when retracted. Allows hook to rotate up without servo which would not support load of the robot by putting tension on the chain as the actuator extends.

Highlight: When our actuator motor overheated in competition, requiring 4 engineers to fan it out for 5 min.

Quote: "Kind of effective, sometimes." -Timmy, lead programmer

# data[].attributes.body
Name: Iris

Creativity: Uses a retractable intake mechanism to grab pixels from the stack and the floor. It uses a suspension on the retraction linkage to increase intake robustness and reduce servo strain.

Highlight: When our robot decided to take a break during a game by pulling the power switch cable.

Quote: "Avoid ESD PTSD at all costs" -Angelos, programmer

# data[].attributes.body
Name: Pollinator Prime

Creativity: Placing system is modeled after an arm, with a shoulder, elbow, hand, and 5 fingers (4 for placing pixels and 1 for adjusting pixels). It swings out from the intake to place, and it is also how we suspend.

Highlight: Scored 6 of the top 10 scores in Utah (our region) and won Winning Alliance Captain 3 times this season (out of four competitions)

Quote: Our robot is modeled after the Six S’s for Successes, “Simplicity, Symmetry, Strength, Stiffness, Stability, and Speed” from our Coach Royd.

# data[].attributes.attachment_caption
A front view picture of our robot that shows its ramp and slide mechanisms.

# data[].attributes.body
Name: Viti Tawiti

Creativity: Our claw is designed to perfectly clamp on to a pixel that comes from the ramp, and it can deposit a pixel in a single motion. This made it very easy to score pixels once we made it to the backstage.

Highlight: When our robot decided to disconnect its own servo wires so we couldn't use it during a match.

Quote: "Guys this is the first time I’ve made anything that works" -Ori, lead builder

# data[].attributes.body
Name: Pirsus V3

Creativity: End effector with 4 degrees of freedom, active intake (with flippers!), and cool curvy custom drive train.

Highlight: Full V3 rebuild in 3 days

Quote: "Did you Loctite it?" -Coach Decker

# data[].attributes.body
This is our robot, Monarch, at the begining of the season (could not find an updated picture)

# data[].attributes.body
Name: Purple Pixel Eater

Creativity: Custom cast silicon intake, full 3d printed custom drivetrain, a few parts using a branch of AI called generative design, and a custom tape measure lift.

Highlight: Being featured in a First Updates Now video: https://www.youtube.com/watch?v=fq87_F5Ykec

Quote: "Have you ever noticed that Jacob (our programmer) has chicken nugget colored hair?" -One of the various comedians/clowns that make up our team

# data[].attributes.body
Name: Brad

Creativity: To ensure the Pixel placement within is the same every time, we have 3 independent passive mechanisms on the Magazine: a one-way door, passive top flaps, and compliant inner strips. Once the pixels are propelled up the ramp into the Magazine, the compressed one-way door at the entrance springs back up, preventing the Pixels from sliding back out. The Pixels automatically reorient themselves into the optimum position for pick-up as they are restricted by thin and flexible 3D-printed inner strips inside the Magazine. Furthermore, the spring-loaded Magazine top flaps remained closed until being lifted open solely by the automated motion of dropping the outtake arm to grab, further preventing the Pixels from flying out.

Highlight: NorCal FAC 2x in a row, 274pt MTI sub + one of the first 2+8 autos w/out extendo, FUN Final Top25 Snub pick

# data[].attributes.body
Name: Avalanche

Creativity: We combined our drone launcher with our climber to save space and allow us to adjust the angle for more consistent shots!

Highlight: Qualifying for worlds for the first time ever this year!

Quote: Crazy? I was crazy once… -Lead Programmer Allen

# data[].attributes.attachment_caption
A pictue of our robot with it's telescopic arm fully opened.

# data[].attributes.body
Name: Diablo

Creativity: has a passive climb mechanism that climbs using two servos.

Highlight: When it almost hit a referee in autonomous

Quote: "Build a better robot next time" - head ref

# data[].attributes.body
Name: Bingus the great

Creativity: coaxial tilt mechinism allowing us to have a very compact tilt/stringing, custom drivetrain, claw with distance sensors, custom carbon fiber slides

Highlight: winning a finals match against the best team in our league, before having expansion hub disconnect in the third and loss

Quote: nooooooooooooooooooooooooo

Owen, cocaptian, lead code, lead build

feel free to ask for more info, im owen ftc9987 on the ftc discord

# data[].attributes.body
Name: Buster

Creativity:

We were able to make many optimizations to the REV Duo Starterbot, such as adding a wedge to passively lift the stage door, a drone powered by a rubber band, a redesigned claw that can pick 2 pixels at once and drop them individually, and hooks for our hanging mechanism.

Highlight:

This was our rookie year, and we've had an amazing season. We reached an OPR of 125, and won the SD interleague (WA1) and the SD regionals (WA2). Our 2+0 auto and hang were successful for 15 matches in a row.

Quote:

"It's RoBustin Time"

# data[].attributes.body
Name: Atlas

Creativity: won design!!!!

Highlight:

:3 he stronk

# data[].attributes.body
Name: Garrett

Creativity: inspiration from a human's arm in constructing the intake/outtake. A worm gear drives the main arm up and down, followed by a servo that moves the forearm and wrist, allowing the arm to reach over the chassis and drop pixels in front or behind itself with ease. 2 more servos control fingers with "tendons" and "muscle" that allow it to grab pixels in tight spots and easily recenter pixels from a wider range. Thanks to the worm gear we can also just use a single c channel on the arm to hang flawlessly.

Quote: "it's gripping time" and the robot gripped all over the place" -Josh, freshman fabricator

# data[].attributes.body
Name: Onilim

Creativity: The mechanism for grabbing pixels has been devised to hold two at a time, making it possible to accumulate more pixels in a shorter time.

Highlight: Participated in the semi-finals as a second team.

Quote: "We all worked hard to adjust the robot until midnight the night before, so I'm glad it's working properly." - Nodoka, a hardware member.