# data[].attributes.body
The ball hits the roll of tape it rolls and collapses the jenga knocking the dominoes over hitting the car going down the ramp hitting the tennis ball landing inside the cup

seven steps

the car falling over because its very difficult to balance

make more steps because it feels too short

# data[].attributes.body
We had two people go to a dance club get into a dance battle then later just hug it out

Yes, the dancing turned out very well

I would make the movie longer with more scenes

# data[].attributes.body
I made a level where the theme was a big forest adventure, the characters are a buff guy and a buff villian.

I have no pictures or screenshots becuase my game crashed and deleted everything

I would make longer more intresting levels that are more fun

# data[].attributes.body
We were supposed to make a candy dispenser with a mechanism to release a certain amount of candy with a button lever etc.

You push the popsicle stick and it creates a hole for candy to leave, then pull it back for the candy to stop dropping

It worked because I had measured everything correctly and had put a little twist on it myself.

# data[].attributes.body
We were supposed to make a working pinball machine with a marble drop, moveable flaps, at least four obstacles, marble deposit, legs, and a theme.

We had a football theme where the marble would fall and then use the flaps to hit the obstacles

I liked our theme because it came out like i wanted it to look like

I would make make the flaps work much better and remove the felt for less friction

# data[].attributes.headline
We were supposed to make a device by coding and using makey makey to make a game, sounds or anything else.

# data[].attributes.subject
We were supposed to make a device by coding and using makey makey to make a game, sounds or anything else.

# data[].attributes.body
My device would make different characters whirl or turn into pixels
My prototype did work the makey makey worked with the code that I wrote and my device was able to work
Myprototype worked because i wrote correct lines of codes with the buttons that I instructed makey makey to react with

# data[].attributes.body
We were supposed to create a boat that would not exceed 8x8x8 inches and could hold 40 grams worth of pennys and be able to move 20 inches.

We tested our prototype by putting in in the water tubs putting the 40 grams worth of pennys on it and use our propeller to make it move our boat floated with pennies out of our 10 trials however it could only move an average of with an average of 5 inches out of our trials.
Our prototype did NOT work in order to improve our design we should have made it more light weigh and made a different styled propeller that can spin for a longer amount of time

# data[].attributes.body
Our bridge

# data[].attributes.body
We tested the bridge by putting it on the table and then using a bucket with a bunjee cord and putting sand in the bucket for the weight, our bridge held 4lbs

# data[].attributes.body
Make a bridge out of pasta that can hold up to 5lbs and be 11 inches long.

# data[].attributes.body
No, our prototype did not work and the egg cracked and did not survive the fall. In order to improve our design I believe that we should have had a wider parachute for more air resistence and more cushioning around the egg so that the final hit at the end does not break the egg.

# data[].attributes.body
We tested the protoype inside by dropping it off the table with a fake egg. Then we tested it by going to the top of the bleachers at The Mason Middle school dropping it off the top. Our results were not great as our egg cracked when it landed on the ground. It did not survive the fall.

# data[].attributes.body
Build a device that will hold and protect an egg from a 15-20ft drop, in order to complete the challenge the egg needs to be unharmed( no cracks or breaks)

# data[].attributes.body
Our prototype did not work, what I think we could have done to improve our design is to make our catapult much more sturdy by making a base and to make the popsicle sticks straight and not crooked.

# data[].attributes.body
Our prototype did not work, we should have put an arch at the top of the bridge however ours broke and we were not able to do that.

# data[].attributes.headline
Explain how you tested your prototype and what your results were.

# data[].attributes.subject
Explain how you tested your prototype and what your results were.

# data[].attributes.body
We were not able to get 8/10 times, the best we were able to do was 3/10 times

# data[].attributes.body
Our Catapult

# data[].attributes.body
Build a catapult that can launch a ping pong ball into a target at least 8 out of 10 times