# data[].attributes.body
Mmxnfhjf

# data[].attributes.body
Bfnfnfd

# data[].attributes.body
No xx. 'An.            F. Did bdndbdbnefnj n c

# data[].attributes.body
http://www.hellokids.com/t_7231/origami?rub=401

Here is a link to other Origami that you can do! I hope it was fun!

# data[].attributes.body
And you are DONE! You have made a Dinosaur!!

# data[].attributes.body
Fold the angles inward to make a round belly for the dinosaur.

# data[].attributes.body
Here is another angle.

# data[].attributes.body
When you lie it down it should look like this, with its belly that opens.

# data[].attributes.body
After folding it away from the face, you are going to take the piece going away and fold it forwards to create the feet. It is almost like an accordian.

# data[].attributes.body
Now you are going to fold part of the legs going away from the dinosaurs head, for both legs.

# data[].attributes.body
Flip and fold down the legs on the other side!

# data[].attributes.body
Now you afre going to create the legs! On the tail end of your dino there are three parts. Fold the first sides on the dino downwards to make legs.

# data[].attributes.body
There is a little part pointing out of the front of the dino. If you fold it inwards, but leave a little out, you create his front legs.

# data[].attributes.body
After folding it back along the crease it should look something like this!

# data[].attributes.body
Other side being folded.

# data[].attributes.body
Once side being folded.

# data[].attributes.body
You are going to unfold it once again and fold it the same way, but smaller, one more time.

# data[].attributes.body
Once you fold it back up along the crease it should fold into this!

# data[].attributes.body
Here is a picture of folding the other way.

# data[].attributes.body
Fold higher up than before, on both sides.

# data[].attributes.body
If you flip it around it should look something like this.

# data[].attributes.body
You are now going to open up you dino, so it looks like this again, you can see the creases from before that you made.

# data[].attributes.body
After you have make all your creases, and folded the extra flap under, if you fold along the cut in the middle it should look like this!

# data[].attributes.body
After you make your creases you should fold the extra flap on the bottom, under to the other side so that it looks like this. Reference the flap present on the picture above if this is confusing.

# data[].attributes.body
After you make the creases when you unfold it, it should look like this.

# data[].attributes.body
Fold the other side the other direction to get creases on the other side.

# data[].attributes.body
Now that you have made a diamond shape you are going to take the side that is not split down the middle, and you are going to make creases for the head of your dinosaur.

# data[].attributes.body
You are going to open it up, and create the diamond hape again, but on this side.

# data[].attributes.body
Once again, open up ypur kite shape.

# data[].attributes.body
After you make a diamond on one side, you are going to turn it around and do it on the other side!

# data[].attributes.body
After creasing it upwards you will have created a diamond shape.

# data[].attributes.body
This is what it will look like halfway through turning it into a diamond. The top part of the kite shape will stay flat.

# data[].attributes.body
Towards the bottom is a flap that should open up. You are going to open it and push it upwards to create a diamond shape.

# data[].attributes.body
After you make the creases you will open the kite shape that you made.

# data[].attributes.body
Now that you made your kite shape you are going to take the extra flap on top and make a crease across the top, both forward and backward.

# data[].attributes.body
You are going to then flip it around and do the same to the other side. It will look identical on both the front and back.

# data[].attributes.body
The next step is going to look like this. You are going to fold two sides inward, and it creates a kite shape.

# data[].attributes.body
It should end up looking like this when folded down. (Make sure that the area that is open is on the bottom, is facing you.)

# data[].attributes.body
This next step is a bit harder. After you have all of your creases made, your paper should naturally fold inward and create this shape. (Make sure that the area that is open is on the bottom, is facing you.)

# data[].attributes.body
Then you are going to fold it across the middle, both ways so that you have 8 creases and 8 different triangles on your paper.

# data[].attributes.body
Now you are going to have a square! You are going to now fold the corners diagonally so that there are creases that connect the edges.

# data[].attributes.body
You are going to open it up and be left with something like this. You should be able to tear the top off after having folded it. If you need some extra help, I like to lick the crease and then try and tear it apart.

# data[].attributes.body
You are then going to fold over that extra paper, both ways, to make it flimsy.

# data[].attributes.body
For the next step we are trying to make a square piece of paper, so what you are going to do is grab the corner of your paper and take it to the edge. You will have some extra at the end, but thats okay! (If you have a square piece of paper already you can skip this step).

# data[].attributes.body
For the first step you are going to start to by grabbing a piece of paper! I used a piece of copy paper!