# data[].attributes.body
Three tools I used were toothbrush to score. And the needle tool to cut the shapes out. And sponge to smooth the clay. Two problems I had could not get the handle to stay score deeper and use less slip. Problem 2 no was falling a part use Newer clar or put slip into clay. Making mugs and baking you half to follow directions. In both you heat up the product. Food is edible clay is not. Cook food at a lower temperature

# data[].attributes.body
One tool is the toothbrush you can put slip on it and make clay stay. You can also use the rib tool to make the mug smooth. The last one is the feddling knife I used it to cut the clay at a 45 degree angle on the place that you are going to glaze.

I had problems getting straight lines for when I cut out the body. Another problem is putting the mug together .

in cooking you role dough and in

# data[].attributes.body
A tool we used was the toothbrush to put the slip on the mug and make it smoother.Another tool is the rib tool. it makes the mug so smooth that you can't see cracks
and you can smooth out the part you connected the sides together.There is another tool called the needle.The needle can cut the clay smoothly and you scratch the clay then you put slip on it and connect it to the mug.
1. A problem I ran into is I put the mug on the wheel and put slip on the bottom and I didn't put the canvas type thing on the wheel so my mug sticked to the wheel,
2. When I was painting I dropped some paint in the middle of the mug and and it splattered the color so I used a lot of different colors and splattered the paint in the cup and it turned out so well.
baking is similar to clay because if you were cooking with doe its just like clay you role it out and mold it just like baking. Also paint and frosting are similar to each other. something different about them is you can't eat clay but you can eat doe and you don't use the same tools. Another similarity is they both can cook with the clay its the kiln and with the doe its the oven.

# data[].attributes.body
1 you need the needle to cut the clay.2 you need a fettling knife to cut the angles.3 and you need a tooth brush to put slip on the mug.

1i had a problem putting the mug to together 2 and I had a problem cutting the angles.

solutions when the mug would not to go together but my solution is to put slip on the mug

# data[].attributes.body
1: One of the tools are the needle that is used to scratch up the places that you are going to glaze.
2: Another tool is the toothbrush to glaze the place that you scratched up.
3: the last tool I'm talking about is the feddling knife that you use to cut a 45% angle on the side you glaze.

1: a problem is that your handle is falling off with means you need to smoothen the places you connected the handle.
2:  If your paint is too light you can leave it or add another coat of paint on the color.

# data[].attributes.headline
Sophie 6-4                                

# data[].attributes.subject
Sophie 6-4                                

# data[].attributes.body
The Needle that cuts clay,                                The Fettling knife makes the angles,          The tooth brush puts the slip on it! When I was making the mug       1: I had to swoop the sides up because it kept falling, and I had to restart once because I forgot to slab and slip it                                        2: I made it to thin so I had to start over and not roll it out as much!

# data[].attributes.body
The needle that cuts clay.Fettling knife this makes the angles.The toothbrush puts slip on the clay.When I was making a mug it kept falling  but then I started using tools to make it stand up.

The handle would not stay on so then I added more slip.

With backing you have to make sure you use the amount that it says and with art you have to add the right amount of slip.

With mugs and cupcakes you have to bake both of them.

# data[].attributes.body
The wheel is used for glaze and putting the mug together, it is a helper. The rolling pin is used for rolling out the clay. The toothbrush is used for slip and attaching. 1 problem: Is I would apply glaze and I still saw white
Solution: I would just reapply.
2 problem: I did not like my design, i messed up
Solution: I got a rag and wiped it off. Compare and Contrast we fire they bake!

# data[].attributes.body
The rolling pin was used to roll out the clay and make it even.

The Fettlling knife was used for making 45 degree angles on the clay to stick it together.

The tooth brush is used for applying slip to the clay

One problem is the clay is to light the solution is put another layer on.
Another problem is if you make a mistake then the solution is to wait till it dries and go over it again

A compare is we cook the food and the mugs and the contrast is that we use a kilm and they use a microwave

# data[].attributes.body
I think I did my best because it looks like what I expected it to look like but when making the mugs I used a rolling pin , fettling knife , sponge and much more . 1 problem was that I forgot to keep the base thin like a pancake so I simply fixed it by simply re-rolling it . Another problem was that I did not cut the clay so I .I did not finish this.

# data[].attributes.body
Rolling pin was used to role out the clay and make it evenly based not to thin but not to thick!
The Fettling life was used to cut any certain slab at the angle of 40 degrees.
The sponge was used to make the clay smoother.
Solution: If you made a mistake on a design you can go ahead and smooth it off. And you can go back and start again with the same design but you have to be aware of to much glaze.
Problem: do not but to much glaze on and to the point its messy. And will not look as good.
Solution: Make sure to wipe off all the extra glazer back into the bottle so we can save as much glaze as possible!
Problem: Make sure u get a brush to help pour all of the axis glaze in the bottle

# data[].attributes.body
The slip is used to stick the body, handle, and base together, the toothbrush to add on the slip, and the fettling knife to cut the fly correctly. One problem is that you might add too little glaze or the shade is too light. The answer to this is simple: just add more glaze to the bare or light spot. Another problem is that the handle can easily break. You'll have to add as much clay as needed in order to prevent this.

# data[].attributes.body
The fettling knife was used to cut slabes of clay into 45 degree angles.
Toothbrush was used to applying slip.
The rolling pins were used to flatten out clay pieces.
One problem I ran into was when I made the base too thick so I had to go through roll it out again and recut it.
My second problem I found was when I made the clay to thin, what I had to do to fix it was re-kneed the clay piece and cut it out again.

# data[].attributes.body
The tooth brush is used for appling slip to the clay. The fettling knife is used for making angles. The needle is used for cutting the clay.
Problem: Sometimes I would start building the mug but then it would fall over.
Solution: You use the tools to help it form.
Problem: I would make the clay to thin.
Solution: So I would have to kneed it.

# data[].attributes.body
To make our mug we used, a needle, a sponge and slip. One problem was the clay being to thick for the sides. too fix that we roll the clay out more tell it was a good shape. One problem was when we were putting the mug together it would not stick so we had to make a 45 degrees angle than we added slap to stick. there are way different tools it has more or less steps.

# data[].attributes.body
The fettling knife is used for cutting the clay. The sponge is used for making sure the clay is smooth. The rolling pin is used to roll out the clay into a slab to make the body of the mug.
1. One problem that I had was when I was making the mug I made it too thin so it wouldn't be even. Then I re rolled the slab so that it was thicker.
2. Another problem I had was making the base thin like a pancake, but then i just re-rolled it so that it was thinner.
Baking and ceramics both have to have heat. When you bake you have to use an oven, and when you make a ceramic it has to go in the kiln. Also it takes steps for each of them to get to the kiln and the oven

# data[].attributes.body
Tools you need are need a needle, a roling pin and a sponge.
Problem: Putting the body and bottom together.
Solution: Trying your best, retry if you failed the last time.
Problem: Making sure that the body is not to thin or fat.
Solution: Watching how thin you make it so it is not to thin or to fat.
A compare is food bakes in a oven and clay bakes in a kiln. A contrast is clay you can make anything you want to make and baking you bake something way different than what you made with clay

# data[].attributes.body
The tools I used were sponge, needle and rolling pin. the sponge helped smooth out the clay and soften the corners. the needle helps cut the clay with precise cuts. the rolling pin, of course rolls out the clay. The first problem I had was rolling out the clay, sometimes the clay was really hard and you really had to roll it. My second problem was slipping and scoring, attaching all the pieces was a bit difficult for me to do. Baking and ceramics both require some type of heat source, kiln, oven. you have to add ingriedients in baking