# data[].attributes.body
I think we should use a fin like this. It looks more aerodynamic than some other fins here. It also looks like it will help our fins stay balanced.

# data[].attributes.body
I think we should use two or four fins to see the difference, I also think we should use a fin like the one in the picture below. Also I think that we should put them more equally on the rocket. Here's the picture:

# data[].attributes.body
what fin?

# data[].attributes.body
I think that our next rocket should have two or four fins not three and not one. Also I think that the fins should be more even because the fins we had on our rocket were uneven.

# data[].attributes.body
For our rocket fins, I think we should use Styrofoam and cover it in duck tape. We should connect the fins to he body of our rocket with 3M strong duck tape. I also think we should have one set of fins at he very bottom and one closer to the top. The one that's up at the top should be smaller by and 1 inch I or so . I think the set of fins a the bottom should be 4 - 5 inches and the one at the op 3 - 4 inches. We should also put the set of fins a he bottom under ( as Kyle showed) for good balance when our rocket launches.

# data[].attributes.body
I think our fins should be made up of styrofoam because it will be light and easy for the rocket to be controlled. I also think that Kyle's posts are also very reliable. Also, we shouldn't have big and bulky ones, we should have small and light ones because it will be easier for the rocket to fly. (click on the image for more)

# data[].attributes.body
I think we should use a fin that looks like this. I say this one because this looks like it will be the most balanced and we want it to stay balanced during takeoff and in mid-air.

# data[].attributes.body
Here is a picture of a type of engine. I think Ms. Lian is supplying us with an engine.

# data[].attributes.body
We need to have fins on our rocket to make sure that our rocket can stand up. Here are some fin deigns.

# data[].attributes.body
I would say this rocket kind of looks like the one we just saw. LOOKED! Not IS!! Maybe we can base our rocket on this.

# data[].attributes.body
I think we should have a nose cone like this because it is the most aerodynamic and all rockets use this nose cone

# data[].attributes.body
I think that our rocket should be narrow and on the lighter side. I think this because going back to Newton's third law. If our rocket is lighter then gravity will have less control over it.

# data[].attributes.body
For fins I think we should use card board triangles and cover them in duck tape and then use then strong duck tape to  tape the fins on the sides of the vintage seltzer bottle.

# data[].attributes.body
I think we should have this because this connects to my idea with coke and mentos to give it power on the bottom

# data[].attributes.body
Here's a diagram or a picture for inspiration.

# data[].attributes.body
Anna this mostly goes out to you, but Will and Kyle should pay attention to this as well. I think we should use the 3M Tough duck tape and maybe a type of glue for it to be fully together. Maybe like a hot glue gun or something.

# data[].attributes.body
I don't think we should use the strong duck tape because it weighs more then regular duck tape so I think we should use this because its light and it wont weigh down the rocket

# data[].attributes.body
I think we should use this recycled paper for insulation in our nose cone and body of our rocket. I think this because it will keep our rocket cool.

# data[].attributes.body
I think we should use strong 3m duck tape to connect our fins to the body of our rockets. This is a good idea because our rockets will be ruined it a launch off the fins fall off. 3m duck tape also is known for being very light and great quality and better at sticking then just normal duck tape. 3ms tape is also known for being used in many places as they own scotch tape.

# data[].attributes.body
I think we should use this because its very light and its made out of light plastic, and if the nose cone is light then the rocket wont be weighed down and it has a flat top.

# data[].attributes.body
I chose this picture because it shows the different kinds of nose cones and how fast the rocket went with depending on the shape of the nose cones it has.

# data[].attributes.body
I think we should use a vintage seltzer bottle for our base because it has a good sturdy base that has a strong plastic so unlike the balloon rocket, it can't be easily popped.

# data[].attributes.body
WILL

# data[].attributes.body
I see that these have  the most popular nose cones and I think that we should decide from one of these nose cones.

# data[].attributes.body
I want to include this nose cone on our rocket. If you click on the picture you will go to a google images page that has a lot of pictures on nose cones. I think we should have a nose cone because the rocket could go faster and the rocket will look more sophisticated. The nose cone "slices through the air to make it faster".