# data[].attributes.body
MATERIALS

2 Plastic bottles

technopor

Paint

microporous frosted

Silicone rod

TOOLS

Ruler

Brushes

Silicone gun

Cutter

INSTRUCTIONS

First, wash, and dry the two plastic bottles completely.

Then, cut the tip off the first plastic bottle and then glue it to the bottom of the second bottle with hot glue.

Next, paint the bottle the color you prefer and decorate it.

After that, use a large piece of Styrofoam to make 3 fins for the rocket, paint it the color of your choice and then decorate with frosted microporous.

Finally, we glue the fins to our rocket and that's it.

YOU ALREADY HAVE YOUR ROCKET MADE WITH PLASTIC BOTTLES.

# data[].attributes.attachment_caption
This is a project created to encourage recycling and creativity, while contributing to the environment by reducing pollution from the waste of plastic bottles and putting them to better use.

# data[].attributes.headline
TURTLE FLOWERPOT WITH RECYCLED PLASTIC BOTTLE 

# data[].attributes.subject
TURTLE FLOWERPOT WITH RECYCLED PLASTIC BOTTLE 

# data[].attributes.body
I. TOOLS::

·Cutter

·Scissors

·Brush

·Glue gun

·Nail

·Lighter

II.  MATERIALS

·   1 plastic bottle

·   5 caps

·   Tempera or spray

·   Moving eyes

·   Technopor ball

·   Color sheet

III. SAFETY RULES

·   Maintain an adequate distance from sharp tools.

·   Materials and tools in good condition.

·   Have good management of tools and materials.

·   Use gloves to avoid cuts or other damage.

IV. INSTRUCTIONS

1. First, collect materials and tools.

2. Then, mark where the bottle is going to be cut.

3. Next, cut the bottle.

4. After, paint the bottle piece in the preferred color.

5. After that, using a nail and a lighter, carefully heat the tip of the nail and make breathing holes at the bottom of the piece of bottle.

6. Then, with the silicone gun, glue the 4 caps under the bottle.

7. Next, paint the Styrofoam ball and glue the movable eyes, with the marker mark a mouth under the eyes

8. After, with the colored sheet, put a lid on top and mark the visor that will be for the turtle's cap, cut it out and glue it under the lid without covering it too much.

9. Then, glue the little cap on the turtle's head.

10. Finally, glue the turtle head to the front of the bottle piece.

Now, you have a cute turtle planter made with recycled materials!

# data[].attributes.body
Desk Organizer with recycled cardboard

TOOLS:

•Scissors

• Cutter

•Rule

• Silicone gun

Packing tape

MATERIALS:

• 2 cardboard boxes (milk or oil)

• Hot silicone

• Decorative paper

•Pencil

• 2 skewer sticks

SAFETY STANDARDS

• Have tools and materials in good condition

• Do not play with tools or equipment, because you could cause an accident.

• Work with clean, dry hands

• Hold your hair

INSTRUCTIONS:

1.-First, cut the cardboard with the following measurements:

8x8: 4 pieces

8x25: 2 pieces

8.5x24: 1 piece

25x25: 2 pieces

25x18: 1 piece

23x16: 1 piece

23x5: 2 pieces

24x17: 2 pieces

16x5: 2 pieces

25x7.5: 2 pieces

25x17x10x9x15x8: 4 pieces

2. Next, glue the double and quadruple pieces together:

8x8: After gluing, you'll have 2 pieces.

8x25: 2 pieces.

24x17: 2 pieces.

25x25: After gluing, you'll have 1 piece.

25x8x9x15x17: After gluing, you'll have 2 pieces.

3. After that, glue the 8x25 cm cartons to the sides of the base of the 25x8x17x9x15x10 cm carton

4.After that, we glue the 8x8cm cartons in the middle of the base, keeping the same distance

5. Then, Glue the cardboard (its measurement is 8x25 cm) on the front of the 8x8 cm cartons

6. Then, glue the anticucho sticks to the side but in the measurement of the height of the cardboard

7. Then, glue the cardboard measuring 25x18 cm on top and to the base.

ELABORATION OF THE LITTLE BOX

The pieces to be used are of the following sizes:

-25x7.5: 2 pieces
-16x5: 2 pieces
-23x5: 2 pieces
-23x16: 1 piece

1.First, glue the 16x5 cm pieces to the leftover sides of the 23x16 cm piece

2. Then, glue the 23x5 cm pieces to the leftover sides of the 23x16 cm piece

3. After that, glue the 25x7.5 cm piece to the side of the 23x16 cm cardboard and line it with decorative paper and put a ribbon or cardboard on it to be able to pull it out.

FINAL STEP

10.Finally, stick the decorative paper all around the cardboard until you can cover the entire area and finally enjoy our recycled desk

# data[].attributes.body
MATERIALS

- 3 plastic bottles

- 15 caps

- Sticks

- Paint

- Candlewick

TOOLS

- Tape

- Paintbrush

- Scissors

- Silicone gun

INSTRUCTIONS

1. Firts, collect and clean all recycled materials.

2. Then, cut a litter square in the side of the two bottles.

3. Next, with the third bottle, cut below half and clase the hole of the biggest part and the other part glue it to the end of the other vertically.

4. After that, with the bottles that we have cut squares and the bottle that has the complement glued, we drill two holes on the opposite side with parallel exits to be able to insert the sticks.

5. Next, cut the insertd sticks to the limit measurementof the width of the bottle the at each end of the sticks paste the taps with the silicone gun.

6. Finally, tie with the candlewick every coach of train, consider the firts coach as the cab of the driver.

7. Now, paint the coaches with the colors you prefere and put a cardboard in shape of tube as tailpipe.

¡AND YOU HAVE YOU RECYCLED TRAIN!

# data[].attributes.body
Materials

Plastic Bottles

Painting

Wick

Glue

Marble

TOOLS

SCISSORS

RULE

PAINTBRUSH

INSTRUCTIONS

1. MEASURE THE BOTTLE AND MARK WITH A MARKER WHERE WE ARE GOING TO CUT IT.

2. Cut the bottle

3. PAINTING AND DECORATING THE BOTTLE.

4. CUT THE WICK.

5. WITH THE RUBBER BAND STICK THE WICK TO THE BOTTLE CAP AND THE WICK TO THE BALL.

6. TO MAKE THE BALL JOIN WITH THE ROPE, GLUE THE TIP WITH GLUE AND BAG THE BALL WITH WICK.