# data[].attributes.headline
Reagan Richardson - How to Make a Water Purifier With Charcoal

# data[].attributes.subject
Reagan Richardson - How to Make a Water Purifier With Charcoal

# data[].attributes.body
Step 1: Find activated charcoal and crush it to make a powder consistency.

Step 2: Rinse the activated charcoal, and spread it on paper.

Step 3: Make a filter using a 2L water bottle.

Step 4: Grab materials for the filter such as pebbles, dirt, sand, a cloth, large rocks, etc.

Step 5: Build the water filter. The cloth goes at the bottom, then activated charcoal, then sand, next pebbles, and lastly, your large rocks.

Step 6: Finally find a clean body of water, and put it in your water filter.

# data[].attributes.headline
Damian Contreras - how to make a water purifier with charcoal 

# data[].attributes.subject
Damian Contreras - how to make a water purifier with charcoal 

# data[].attributes.body
Step 1: Get activated charcoal from hardwood and crush it into a powder.

Step 2: Rinse the activated charcoal and lay it on a piece of paper to dry.

Step 3: make a filter vessel with two liter plastic bottles.

Step 4 : Use gravel or sand as pre filter media.

Step 5: The filters from bottom to top are tight-knit cloth or a coffee filter, activated charcoal, sand, small pebbles, and finally at the top is large pebbles or grass.

Step 6: Pour the water into the water and wait for the water to become safe to drink

# data[].attributes.body
To make a water purifier with charcoal, you'll need activated charcoal, water, a filter vessel, and pre-filter materials. First, you have to get the activated charcoal and rinse it. You'll have to create your water vessel, gather pre-filter materials, and layer the filter media. Finally, pour water into the filter and the pathogens will die, and then you can have purified water.

# data[].attributes.body
Step 1: First, you have to place poles in the ground to form your foundation.
Step 2: Second, place a cloth such as a bedsheet over the top of the poles to have cover for your habitat.
Step 3: Next, use hooks to make sure the cloth is in place securely.
Step 4: Finally, cut a hole open for the opening so you can get in and out of the tent.
Now you have a fully functioning tent for survival.

# data[].attributes.body
water purifier so then you can make the water drinkable for you to survive.

# data[].attributes.headline
Connor Morgan - How to make a water purifier with charcoal

# data[].attributes.subject
Connor Morgan - How to make a water purifier with charcoal

# data[].attributes.body
Step 1: First, get activated charcoal and crush it into powder.

Step 2: Next, rinse the activated charcoal before using it and then spread it on paper to let it draw.

Step 3: Then, create a filter vessel by using 2-liter plastic bottles.

Step 4: After that, gather materials used for the filter including sand, pebbles, large rocks, and a cloth.

Step 5: Next, finish all the water filter layers using the materials you gathered. Put them in this order from top to bottom: 1. Cloth 2. activated charcoal 3. sand 4. pebbles 5. Large rocks.

Step 6: Finally, Get some water and pour it into the layer at the top of your creation.

# data[].attributes.headline
How to make a water purifier with charcoal- Geetika Reddivari

# data[].attributes.subject
How to make a water purifier with charcoal- Geetika Reddivari

# data[].attributes.body
1. First, collect activated charcoal and crush it.
2. Second, wash the charcoal with water to remove any chemicals on the surface.
3. Next, spread the charcoal on paper and let it dry.
4. To create the water filter, get a plastic bottle or if you do not have a plastic bottle you can use a cloth.
5. Distribute the activated charcoal, some sand, pebbles, and cotton in each layer to filter the water.
6. Pour water into the filter and put a container in the bottle to have filtered water.

# data[].attributes.headline
How to make an air filter with a fan and charcoal(with activated charcoal) WHO DID THIS? 

# data[].attributes.subject
How to make an air filter with a fan and charcoal(with activated charcoal) WHO DID THIS? 

# data[].attributes.body
Supplies: 20x20 standard air filter, glue, scissors, 10x10x10 cardboard box, fan, pencil, razor cutter/box cutter.

Step 1: First, grab your air filter and scissors. Use the scissors to cut the filter into four 10x10 inch squares. Second, grab your cardboard box and glue the square pieces to the inside of the box.

Step 2: To get the shape of the fan, place the fan on top of one side of the box that has an air filter. Use your pencil to trace the bottom of the fan onto the box. Then, use your razor/box cutter to cut and remove the outlined section from the box.

Step 3: Next, using the opposite side of the box with the cut out piece, draw a slightly bigger circle than the section you just removed. Be careful to cut around the air filter on that side.

Step 4: Now, attach the fan to the side of the box with the larger cut out section. It must be positioned to where it blows air away from the cube, not into it.

Step 5: Thoroughly tape the bottom of the box shut with duct tape. Fill the box with activated charcoal from the top. Thoroughly tape the top shut and reinforce the other edges with duct tape. Plug in the fan.

# data[].attributes.body
1- find a long, dry stick. Make sure it's thick.
2- Split the stick halfway down the center, but leave the other half together.
3- Place a flammable object, called tinder, inside the split, such as paper, or thin wood.
4- place a cord or lace in between the split, on the tinder.
5- run the cord through the split down to the very edge.
6- Pull the cord back and forth quickly until the stick starts smoking.
7- The tinder should ignite, and start a fire.

# data[].attributes.attachment_caption
In order to do this you will need,Flint and Steel

# data[].attributes.body
Step 1 - Take your flint in your left hand (if you're right-handed), with the char cloth just underneath the sharp edge of the flint.

Step 2- Then, Strike the steel down against the flint, as if you were trying to shave off a small piece of the edge of the steel, because you are.

Step 3 - After a few strikes a spark will land on the char cloth and you will see a faint glow. The glow will create a ring of red as the ember spreads out away from the point of contact.

Step 4 - Next, fold the char cloth into a smaller square and place it into the nest of the tinder, and fold the tinder over the top to make a small ball. Smoke will float out through the tinder, and a few puffs of air will increase the flow

Step 5- In addition to that,   A steady blow and your tinder will burst into flame.

Step 6 - Lastly, put your tinder ball under your carefully prepared campfire. Stand back and enjoy it. The more wind, the better.

# data[].attributes.headline
How to start a fire without any matches/Lighter- WHO DID THIS?

# data[].attributes.subject
How to start a fire without any matches/Lighter- WHO DID THIS?

# data[].attributes.body
Step 1: Items you need to make the fire
Flint
Steel
Tinder/Wood/Kindlings(Dry)
Rock
Or you could buy a Flint and Steel starter Kit (5$-20$)

Step 2: try getting a spark by scraping the blade of your pocket knife against a piece of flint — a hard, gray rock that fractures easily. Form your tinder into a nest about the size of a softball. Hold the flint just above the tinder and try to direct your sparks into it. Nurse the spark into a flame by blowing on it gently. Add kindling and fuel as needed.

# data[].attributes.headline
How to Make Water Purifier with Charcoal - Kristen Yamashita

# data[].attributes.subject
How to Make Water Purifier with Charcoal - Kristen Yamashita

# data[].attributes.body
(1) The first thing you want to do is make activated charcoal.
--> This is because most charcoal found at stores is not pure and could leach chemical contaminants into the water, which is the opposite of what you want to do when making a water filter! Make the activated charcoal out of hardwood found in the wilderness in survival situations. Crush the activated charcoal into powder.
(2) Secondly, you must rinse your activated charcoal.
--> Rinse to remove any contamination on the surface. Let it dry on a paper.
(3) Next, it is time to create your filter vessel. Often, survival charcoal water filters are made from 2-liter plastic bottles.
(4) Debris, algae, etc. can clog the top layer of charcoal, so it is important to make a layered filter.
--> You can use media such as gravel and sand.
(5) After that, layer your filter media!
--> The order of this filter layer is from bottom to top:
1. Tight-knit cloth or coffee filter (stops any charcoal pieces from getting into water collection vessel.)
2. The activated charcoal (absorbs chemical impurities from water)
3. Sand (or smashed-up brick pieces)
4. Small pebbles (filters out larger pieces of debris)
5. Larger pebbles (or grass) (catches larger pieces of debris in water)
(6) Finally, pour water into the filter and watch as the "gravity filter" (it will take awhile) kills the pathogens and impurities in the water!
--> Further treat the water from the charcoal filter by boiling, household bleaching, or using water purification tablets.
(Source: https://www.primalsurvivor.net/diy-charcoal-water-filter/)

# data[].attributes.body
Materials - To Produce Lights/ Fire
-1 Metal Box
- 2 Candles
Step 1: Remove the wicks from the candles
Step 2: Attach the wicks candles to the box with hot glue
Step 3: Melt the candles in the microwave
Step 4: Pour the melted wax on the lid
Step 5: Take a small sheet and insert matches and attach the igniting part to the box

# data[].attributes.headline
DIY Charcoal Water Filter - Timothy Pinkerman

# data[].attributes.subject
DIY Charcoal Water Filter - Timothy Pinkerman

# data[].attributes.body
Step 1. Get activated charcoal
Detail: You can't use barbecue charcoal because it is not pure, so you will have to make activated charcoal out of hardwood

Step 2: Rinse the charcoal
Detail: Before using, rinse it to remove any impurities, then spread of a paper and let it dry

Step 3: Create your filter vessel
Detail: A typical vessel is a 2-liter bottle, so grab one and cut of the bottom of the bottle so there is an open top

Step 4: Gather pre-filter materials
Detail: You can make a filter with just charcoal but it is recommended to find other things such as gravel and sand.

Step 5: Layer filter media
Detail: Going from bottom to top, the order is:
1. A tight-knit cloth or coffee filter
2. Activated charcoal
3. Sand
4. Small pebbles
5. Larger pebble and/or grass

Step 6: Pour water into filter
Detail: Pour water into the filter, it will take a while

Step 7: Kill pathogen
Detail: The charcoal will absorb impurities in the water, but it doesn't get all of them, so you will have to further treat the water by boiling it, using a water purification tablet, or using a 0.01 micron water filter.

# data[].attributes.body
Step 1: Insert a coin into the potato.
Details: Place the potato on a sturdy surface. Then press the narrow side of a coin into the top of the potato.