# data[].attributes.body
Ο σύνδεσμος περιέχει απλά projects με τη χρήση του arduino. Υπάρχουν αναλυτικές οδηγίες για κάθε βήμα.

# data[].attributes.attachment_link.readable_text
FREE EBOOK (PDF) - Ultimate Beginners Guide To Arduino

The easiest way for beginners to get started with Arduino is by creating circuits using a solderless breadboard. These simple projects will teach you the basics of Arduino Uno, electronics and programming. In this tutorial, you will be creating circuits using the following electronic components:

This tutorial is going to allow you to jump right in and start building circuits. If you need some background on the Arduino Uno board or the tools that are needed, please check out post - Arduino Uno For Beginners.

Before you can start working with Arduino, you need to make sure you have the IDE software installed on your computer. This program allows you to write, view and upload the code to your Arduino Uno board. You can download the IDE for free on Arduino's website.

Once the IDE is installed, you will need to connect your Arduino to your computer. To do this, plug one end of the USB cable to the Arduino Uno and then the other end of the USB to your computer's USB port.

Select The Board

Once the board is plugged in, you will need to open the IDE and click on Tools > Board > Arduino Uno to select the board.

Select Serial Port

Next, you have to tell the Arduino which port you are using on your computer. To select the port, go to Tools > Port and then selectthe port that says

To complete the projects in this tutorial, you will need to download the project code which are known as sketches. A sketch is simply a set of instructions that tells the board what functions it needs to perform. For some of these projects, we are using open-source code that was released by the good people at and. Use the link below to download the zip folder containing the code.

Once the file has been downloaded, you will need to unzip/extract the folder in order to use it.

The first project is one of the most basic and simple circuits you can create with Arduino. This project will test your Arduino by blinking an LED that is connected directly to the board.
Parts Needed

1. Twist a 220 Ω resistor to the long leg (+) of the LED.

2. Push the short leg of the LED into the ground (GND) pin on the board.

3. Push the resistor leg that's connected to the LED into the #13 pin.

This project is identical to project #1 except that we will be building it on a breadboard. Once complete, the LED should turn on for a second and then off for a second in a loop.
Parts Needed
Using a push button switch, you will be able to turn on and off an LED.
Parts Needed

(1) Arduino Uno

(1) USB A-to-B Cable

(1) Breadboard - Half Size

(1) LED 5mm

(1) 220 Ω Resistor

(1) 10K Ω Resistor

(1) Push Button Switch

(6) Jumper Wires

Using a potentiometer, you will be able to control the resistance of an LED. Turning the knob will increase and decrease the frequency the LED blinks.
Parts Needed

(1) Arduino Uno

(1) USB A-to-B Cable

(1) Breadboard - Half Size

(1) LED 5mm

(1) 220 Ω Resistor

(1) Potentiometer (10k Trimpot)

(6) Jumper Wires

By using a PWM pin on the Arduino, you will be able to increase and decrease the intensity of brightness of an LED.
Parts Needed
This project will blink 6 LEDs, one at a time, in a back and forth formation. This type of circuit was made famous by the show Knight Rider which featured a car with looping LEDs.
Parts Needed
Using a potentiometer, you can control a series of LEDs in a row. Turning the potentiometer knob will turn on or off more of the LEDs.
Parts Needed

(1) Arduino Uno

(1) USB A-to-B Cable

(1) Breadboard - Half Size

(1) Potentiometer - Rotary

(10) LED 5mm

(10) 220 Ω Resistor

(11) Jumper Wires

This project will use 8 pins on the Arduino board to blink 8 LEDs at the same time.
Parts Needed
This project will be using an RGB LED to scroll through a variety of colors. RGB stands for Red, Green and Blue and this LED has the ability to create nearly unlimited color combinations.
Parts Needed
A photoresistor changes the resistance a circuit gets based on the amount of light that hits the sensor. In this project, the brightness of the LED will increase and decrease based on the amount of light present.
Parts Needed

(1) Arduino Uno

(1) USB A-to-B Cable

(1) Breadboard - Half Size

(1) LED 5mm

(1) 330 Ω Resistor

(1) 10K Ω Resistor

(1) Photoresistor

(6) Jumper Wires

A temperature sensor measures ambient temperatures of the world around it. In this project, we will be displaying the temperature in the serial monitor of the Arduino IDE.
Parts Needed

(1) Arduino Uno

(1) USB A-to-B Cable

(1) Breadboard - Half Size

(1) Temperature Sensor - TMP36

(5) Jumper Wires

The project will use a piezo buzzer/speaker to play a little melody.
Parts Needed

(1) Arduino Uno

(1) USB A-to-B Cable

(1) Breadboard - Half Size

(1) Piezo Buzzer/Speaker

(2) Jumper Wires

In this project, you will be able to sweep a servo back and forth through its full range of motion.
Parts Needed

(1) Arduino Uno

(1) USB A-to-B Cable

(1) Breadboard - Half Size

(1) Servo

(6) Jumper Wires

Using a switching transistor, we will be able to control a DC motor. If everything is connected correctly, you should see the motor spinning.
Parts Needed

(1) Arduino Uno

(1) USB A-to-B Cable

(1) Breadboard - Half Size

(1) DC Motor

(1) 330 Ω Resistor

(1) Diode 1N4148

(1) NPN Transistor

(6) Jumper Wires

An LCD is a liquid crystal display that is able to display text on its screen. In this project, you should see the words "hello,world!" displayed on the screen. The potentiometer is used to adjust the contrast of the display.
Parts Needed

Make sure your board and serial port is selected in the IDE. To do this, plug your board in and go to Tools > Board >Arduino to select your board. Next, go to Tools > Port >Com (Arduino) to select your serial port.

The long leg of the LED is the (+) positive and the short leg is the (-) negative. Make sure the correct leg of the LED is in the proper pin of the Arduino or breadboard as directed.

It can be easy to put a component or jumper into the wrong pin on the Arduino or the breadboard. Double check the correct pin is being used.

# data[].attributes.attachment_link.title
15 Arduino Uno Breadboard Projects For Beginners w/ Code - PDF

# data[].attributes.attachment_link.description
FREE EBOOK (PDF) - Ultimate Beginners Guide To Arduino The easiest way for beginners to get started with Arduino is by creating circuits using a solderless breadboard. These simple projects will teach you the basics of Arduino Uno, electronics and programming.

# data[].attributes.body
Παρακάτω ακολουθεί ένα project για τη δημιουργία ενός led κυκλώματος. Δίνονται αναλυτικές οδηγίες.

# data[].attributes.attachment_link.description
Make an LED turn on and/or blink. By rowan07.

# data[].attributes.body
Ο σύνδεσμος περιέχει projects με τη χρήση του arduino. Υπάρχουν αναλυτικές οδηγίες για κάθε βήμα. Μερικά από αυτά φαίνεται να είναι πιο εξειδικευμένα.

# data[].attributes.attachment_link.title
17 beginner Projects - Arduino Project Hub

# data[].attributes.attachment_link.description
Interested in beginner? Explore 17 projects tagged with 'beginner'. Find these and other hardware projects on Arduino Project Hub.