# data[].attributes.body
Measuring the tightness of a belt

# data[].attributes.body
Used to measure components that have divination, as deviation cannot be seen by the human eye. This means the gauge is very accurate and can measure a 100th of a millimeter

# data[].attributes.body
measures voltage oms and amps

# data[].attributes.body
A Vernier gauge is used to measure something very accurately to the nearest millimeter

# data[].attributes.body
feeler blade is used to measure gap widths

# data[].attributes.headline
An accurate sliding rule measuring tool, similar to micrometers, that can be used to measure inside and outside diameters as well as depths. There are several different kinds of vernier caliper; the earliest units were merely slide rulers with opposing stepped jaws; however, other versions with the addition of a dial face make even more accurate measurements on a smaller scale. The newest vernier calipers now use a digital readout that measure to the ten-thousandth of an inch or even smaller.

# data[].attributes.subject
An accurate sliding rule measuring tool, similar to micrometers, that can be used to measure inside and outside diameters as well as depths. There are several different kinds of vernier caliper; the earliest units were merely slide rulers with opposing stepped jaws; however, other versions with the addition of a dial face make even more accurate measurements on a smaller scale. The newest vernier calipers now use a digital readout that measure to the ten-thousandth of an inch or even smaller.

# data[].attributes.headline
Dial indicators can measure very small movement very accurately. A dial indicator can tell you when parts show excessive wear, and can help you put parts into precise adjustment. The device usually consists of a round body with an indicator dial, a fixed base or stand, and a protruding rod that does the measuring. A dial indicator usually has a magnetic base, but it can also have another fixing device, such as Vise-Grips, that clamp the tool onto a stationary part. Here are just a few of this tool’s many uses

# data[].attributes.subject
Dial indicators can measure very small movement very accurately. A dial indicator can tell you when parts show excessive wear, and can help you put parts into precise adjustment. The device usually consists of a round body with an indicator dial, a fixed base or stand, and a protruding rod that does the measuring. A dial indicator usually has a magnetic base, but it can also have another fixing device, such as Vise-Grips, that clamp the tool onto a stationary part. Here are just a few of this tool’s many uses

# data[].attributes.headline
speedometer: Actual MPH = 60/minutes x number of miles traveled minutes.

# data[].attributes.subject
speedometer: Actual MPH = 60/minutes x number of miles traveled minutes.

# data[].attributes.body
if the speedometer reading is higher than the actual speed, the speedometer is fast, if the speedometer reading is lower than the actual speed, the speedometer is slow

# data[].attributes.headline
Tyre pressure gage: the checks that should be taken out on this is that the gage is reading the right amount of pressure in the tyre and to check that the pin showing the pressure is not bent or loose. 

# data[].attributes.subject
Tyre pressure gage: the checks that should be taken out on this is that the gage is reading the right amount of pressure in the tyre and to check that the pin showing the pressure is not bent or loose. 

# data[].attributes.headline
Tape measure: you need to make sure it has no creases in the tape measure and that all the measuring points are still on it and that it still wind back in on its own without pushing it in.

# data[].attributes.subject
Tape measure: you need to make sure it has no creases in the tape measure and that all the measuring points are still on it and that it still wind back in on its own without pushing it in.

# data[].attributes.headline
Rule: you need to check that it has no chips in or other damage to it and then u use it to mark stuff out on other objects.

# data[].attributes.subject
Rule: you need to check that it has no chips in or other damage to it and then u use it to mark stuff out on other objects.

# data[].attributes.body
to aid manufacturing and test processes the sensor has all component, element and asic process and test data traceable from 2d-matrix lable affixed to the top of the device. The SCA720 sensor is mechanically rubust and has no deformation up to 70000g. the accelormeter 3D structure uses capacitive sensing techniques that give it sensitive measurement characteristics and offset stability internal inert gas damping of the mems sensing element provides a mechanical low-pass filter that cuts off above 115Hz