# data[].attributes.attachment_link.readable_text
I am excited to share the pattern for my "Favorite Zipper Pouch".

I needed a few gifts and whipped up some zipper pouches. I have made lots and lots of zipper bags. This is the one I always go back to. It holds a lot but isn't huge. I have probably made over 50 of these!

Iron the fusible fleece to the wrong side of the outer bag fabric.

Measure a 1 1/2″ square and cut a notch out of the bottom corners of the outer pieces and the lining pieces. This will create the pleat in the bottom of the bag.

I like to put little tabs on my zipper so the zipper is not directly sewn into the seam of the bag. It reduces bulk and helps it lay flat. I always measure my tabs larger then cut them down.

As you can see, I like to buy larger zippers than I need. You can always cut them down for smaller projects!

Cut off the metal ends of the zipper.

Sew one of the prepared tabs to the end of the zipper. Backstitch several times over the zipper teeth.

Now measure over and sew the tab on the opposite end of the zipper. There should be 1″ of tab on each side. The excess will be cut off in a minute.

Use your zipper foot and sew along the zipper.

Now you do the same process to the other side of the zipper. Place the zipper face down on the right side of the outer fabric. Line up the edges. Layer the lining on top right side down. (pictured below)

Sew the zipper using the zipper foot.

Top stitch about 1/8″ next to both sides of the zipper. This will hold the fabric in place and it won't catch in the zipper.

Make sure the bag is unzipped!!!

Turn the bag right side out.

Stuff the lining down in the bag and press the bag as needed. Done!!!

# data[].attributes.attachment_link.description
I am excited to share the pattern for my "Favorite Zipper Pouch". I needed a few gifts and whipped up some zipper pouches. I have made lots and lots of zipper bags. This is the one I always go back to. It holds a lot but isn't huge.

# data[].attributes.attachment_link.readable_text
I love the look of a zippered box pouch...so incredibly cute. I found many tutorials on the internet, but was disappointed after making pouches following these tutorials to find that they were not fully lined; looks so much nicer when you open your pouch and there are no seams. It took me a long time to figure it out and I thought and thought and thought...then I got it♥ I don't want to keep this knowledge to myself, so here it is. I'd like to thank Jane at Projects by Jane (the only other tutorial like this that I was able to find on the internet - wish I'd found it sooner). Her photos may help you out too if mine fail to communicate properly. If you like what you see and this tutorial was helpful, please help me by making a small donation to my site (click mauve button on top right on homepage).

♥♥♥Thanks so much! ♥♥♥
The finished pouch is 3 high x 4 wide x 7 long (inches) Here's what you need:
1 twelve inch zipper

2 10x7 inch panels for the lining (my lining fabric is the green one)

2 10x7 inch panels for the exterior (my exterior fabric is the brown floral one)

4 10x7 inch panels of fusible interfacing to give the lining and exterior fabric some structure (I have already ironed the interfacing onto the fabric in the photo above)

2 4x3 inch pieces of complementary fabric for the pulls at the end of the zipper

STEP 1. Start by cutting out all of your pieces and ironing the interfacing to the lining and the exterior panels (iron with the bumpy side touching the fabric).

STEP 2. Make marks on your zipper for guidance. Mark the edge of the fabric and mark a point 1/2 inch away from the edge (the tutorial used to suggest 1/4 inch...I have received feedback that people find making this mark at least 1/2 inch from the edge a little easier for the overall project...) - keep this mantra in the back of your mind..."you will not sew beyond this line". Mark this on the lining and exterior fabric as well (note once again..."you will not sew beyond this line").

STEP 3. Next, it is time to attach the first set of exterior and lining panels to the zipper. Sandwich the zipper between the two panels as pictured below:

At the bottom, the lining panel is right side up, then the zipper right side up and on top, the exterior panel right side down (overall, the right side is always facing the zipper and the fabric covers the zipper). Later, you will pull backthe panels to expose the zipper and then top stitch...you will see shortly.

STEP 4. Pin the exterior and the lining to the zipper, like so:

STEP 5. Now, put the zipper foot onto your sewing machine (it looks like a ski). Set it up to sew as pictured below: NOTE - start sewing at the line that you created on the fabric as pictured (very important) and stop sewing at the line you made on the other side...do not sew right to the edge of the fabric:

STEP 6. After sewing, pull back the exterior panel:

pull back the lining and then press:

STEP 7. Make the sandwich of the lining, zipper and exterior fabric for the other side:

and repeat steps 4, 5 and 6 for this side of the pouch.

STEP 8. Time to top stitch beside the zipper to give the pouch a nice finished look. You can take off your zipper foot and use your regular sewing foot. Make sure to top stitch on both sides of the zipper and start and stop at the lines that you drew (AGAIN...do not sew over these lines). You probably don't need to pin before top stitching, but I did here:

STEP 9. Put the right sides of the exterior and the right sides of the lining together and pin for sewing. When you sew, make sure to leave an opening in the bottom of the lining for turning right side out later on (see where I am pointing):

STEP 10. Sew along the exterior panel where pinned using a 1/4 inch seam allowance; sew end to end along the exterior panels.

Sew along the lining where pinned leaving a gap in the middle (I have only sewed down so far. Sew from the other side and then stop so that there is an opening in the middle of the lining. Make sure to go back and forth to secure your stitches):

STEP 11. Fold your pouch so that the seams sit centred on top of the zipper with the exterior on top of the lining (here are two photos to illustrate):

and press like this (make sure seams are centred on top of zipper):

STEP 12. Now is time to put the pulls in place. These help to make the zipper easier to open and close and overall make the pouch more functional (in my humble opinion).

I made the pulls by folding the 3x4 piece of complementary fabric in half, pressing and then opening. Then I folded the edges towards the centre line created and pressed in place. Then fold the whole thing in half and press again (sorry no pictures...let me know if you have any questions). Then I top stitched up each side to keep the pulls together and look nice and finished. Here are my pulls (they complement the exterior fabric quite nicely):

Start at the non zipper head end (as pictured below). Fold one pull in half and sandwich it between the exterior panel layers with the loop facing in and the edges sticking out far enough so that you will be able to sew over them (like this):

STEP 13. Pin the exterior panels together for sewing. Make sure to keep the lining panels out of the way and DO NOT sew over them (see photo below). Sew right over top of the zipper and go back and forth over the zipper once or twice to secure it nicely.

STEP 14. OPEN THE ZIPPER!!!! This is a super important step for two reasons: 1. The zipper head will get stuck on the outside of your sewing line & 2. You won't be able to turn your pouch right side out later on (I've done this before and it sucks if you forget to open the zipper). Open it at least 3/4 of the way open.

Repeat steps 12 and 13 to put the pull in place on the zipper head side of the zipper (I like to pin my zipper to help keep it in place since it is now open♥) and to sew the exterior panels together on the other side:

STEP 15. Repeat the above steps to sew the lining panels together on both sides. This time you will not be sewing over the zipper; just the lining:

It is a good idea to trim the excess fabric and the excess pieces of zipper at this point:

STEP 16. This is the fun part! Now we get to make the corners boxy. This gives the shape to the pouch that makes it so darn cute. First, pinch one of the four corners of the exterior panels:

Here's another angle just in case it's unclear (see photo below): Make sure that the fold visible on top is perfectly lined up with the seam underneath it:

Measure 1 and 1/4 inches from the corner...:

...and draw a line that will be approximately 2.5 inches long:

Sew along that line:

and cut off the excess material:

Repeat for all corners on the exterior fabric. It will look like this when all four corners are done:

Now, repeat STEP 16 for all four corners of the lining.

It will look like this when corners are complete (one lining corner left to trim in the photo):

♥ FINAL STEP: Gently pull the pouch right-side-out through the hole in the bottom of the lining. Make sure to poke out every corner so that your pouch has a nice boxy shape. Hand stitch the hole in the bottom of the lining. CONGRATULATIONS!!! You have one fully lined zippered box pouch.

Here are some others I have made:

Happy pouch making :)

PS: Nail polish worn throughout this tutorial is "For Audrey" by China Glaze.

# data[].attributes.attachment_link.title
Fully lined zippered box pouch - pattern and tutorial

# data[].attributes.attachment_link.description
I love the look of a zippered box pouch...so incredibly cute. I found many tutorials on the internet, but was disappointed after making pouches following these tutorials to find that they were not fully lined; looks so much nicer when you open your pouch and there are no seams. It took me a long time to figure it out and I thought and thought and thought...then I got it♥ I don't want to keep this knowledge to myself, so here it is.