# data[].attributes.body
This picture shows the back of my mug. You can see the hair of my Rick and the handle that i attached. I honestly feel like i should've made the handle a more bigger and thicker one.

# data[].attributes.body
The picture on the left is the ear and the picture on the right is the hair.

# data[].attributes.body
The pictue on the left is wheb i first got done sculpting. I did the same thing with the nose that I did with the eyes. The 'eyebrow' I rolled a piece of clay then i obviously slip and scorred it onto the mug. For the mouth i carved it out with a tool. The picture on the left shows the ears I attached and the hair. The hair doesn't look too great in my opinion.

# data[].attributes.body
The picture on the left is where i scorred amd put slip to make my mug. The picture on the left is what I first did to my mug, I made some eyes by pushing in through my mug.

# data[].attributes.body
Thats my mug after i was done with it & when I was done cleaning it up.

# data[].attributes.body
I connected the two sides by scoring and slipping where they would touch. I then went on and sealed it. I had cut out a circle for the extra slab that i had left over. I slipped and scored the bottom of my mug & the circle cut out and then i connected both and sealed.

# data[].attributes.body
I cut the side corners of my slab in a 45 degree angle as I saw in the demonstration.

# data[].attributes.body
I first started with a slab for my mug. I forgot to take pictures of when i cut it out.

# data[].attributes.body
I placed my flower on a corner because thats where i liked it. And my backgroud was looking too plain so i added swirls. And i really liked how it turned out. But i still need to clean it up a bit.

# data[].attributes.body
I ended up making 3 small petals, 4 medium sized petals, and 5 big ones. I first attached the small ones to a ball of clay. and I continued to add the rest of my petals.

# data[].attributes.body
I pinched the long ball of clay 4 times with two of my fingers. Then I pinched horizantally starting from the middle of my flower petal.

# data[].attributes.body
I stared by making a ball of clay. Then I made a cylinder type shape which i made by rolling the clay in a single direction.

# data[].attributes.body
I connected the wings to the body of the butterfly by making a hole where the wings go and i used slurp to connect the two together.

# data[].attributes.body
This time I carved out the wings details when the clay was a little more dry that my last pair.

# data[].attributes.body
These are the second pair of wings that i made. And I actually liked these because i made them bigger in size, and I also liked the shape because they look more round at the bottom & they way better to me then my last pair of wings.

# data[].attributes.body
These are the first pair of wings i made. I made the mistake of wetting them too much when carving out details. So I re did them, also because I didn't like that they were small & I also didn't like the shape that much.

# data[].attributes.body
I took this picture after i was done putting my slabs together. I also sprayed my hands with water and tried to smooth out the surface and I used the sponge to round up the squared edges.

# data[].attributes.body
I scarpped every surface where my slabs were going to touch each other, then I added slurp to glue the pieces together.

# data[].attributes.body
I put up my slabs to see if I needed to cut off parts of my slabs, and once it looked good enough to me I moved on to the next step.

# data[].attributes.body
I made 2 big slabs to cut out two 10 by 2 inch slabs. And then i cut out three 2 by 5 small slabs. I also sprayed water on my fingers to smoothe out the surface

# data[].attributes.body
I first made a big slab that covered the wareboard then i cut out a piece that was 8 by 12 inches. I then smoothed it out by spraying water on my fingers and rubbing in the slab to make the surface even.